Desa VSGF33NR Installation Clearances, Conventional Fireplace Installation, Continued

Models: VSGF33NR

1 28
Download 28 pages 53.13 Kb
Page 8
Image 8
INSTALLATION

®

UNVENTED NATURAL GAS FIREPLACE

INSTALLATION

Continued

ASSEMBLING AND ATTACHING OPTIONAL BRASS TRIM (Included with Mantel Accessory)

IMPORTANT:Ifyouarerecessingthefirebox in a wall, do not attach brass trim at this time. See Built-In Fireplace Installation, page 13.

Note: The instructions below show assem- bling and attaching brass trim to fireplace.

1.Remove packaging from three pieces of brass trim.

2.Locate four brass screws, two adjust- ing plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 6.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 6).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 6).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim

with hanging screws on side of fire-

place (see Figure 7). Push trim firmly

into place, sliding hanging notches over

hanging screws.

Top

Side

Set

Brass

Brass

Screws

Trim

Trim

 

 

 

Adjusting

 

 

Plate

 

Shim

Slot

Slot Mitered Edge

Figure 6 - Assembling Brass Trim

Trim Hanging

Screws

AssembledMinimum Clearances For SideCombustible Material, Side Wall, Hanging

Notches on

Trim

Figure 7 - Attaching Brass Trim to Fireplace

INSTALLATION

CLEARANCES

CONVENTIONAL FIREPLACE INSTALLATION WARNING: Maintain the mini- mum clearances. If you can, pro- vide greater clearances from floor, ceiling, and adjoining wall.

Carefully follow the instructions below. This will ensure safe installation.

Minimum Clearances For Side

Combustible Material, Side Wall,

and Ceiling

A.Clearances from the side of the fireplace cabinet to any combustible material and wall should follow diagram in Figure 8.

Example: The face of a mantel, book- shelf, etc. is made of combustible ma- terial and protrudes 3 1/2" from the wall. This combustible material must be 4" from the side of the fireplace opening (see Figure 8).

B.Clearances from the top of the fireplace opening to the ceiling should not be less than 42 inches.

 

 

 

 

 

 

 

 

 

 

121/4

 

 

 

 

 

 

 

 

 

 

 

101/2

 

 

Example

 

 

 

 

 

 

8 3/4

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

INCHES

 

 

 

 

 

 

 

 

 

 

51/4

 

 

 

 

 

 

 

 

 

 

31/2

 

 

 

 

 

 

 

 

 

 

13/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7/8

 

 

 

 

 

 

 

 

 

 

 

7/16

 

FIREBOX

.5

1

2

4

6

8

10

12

14

16 *

 

 

 

 

 

INCHES

 

 

 

 

 

*Minimum 16 inches from Side Wall

Figure 8 - Minimum Clearance for Combustible to Wall

CONVENTIONAL FIREPLACE INSTALLATION

Conventional installation of this fireplace involves installing fireplace along with the corner or cabinet mantel with hearth base accessories against a wall in your home (see Accessories, page 22 and 23). Follow the instructions below to install the fireplace in this manner.

Note: The instructions below show installa- tion using the cabinet mantel and the G3000F/G3001U/G3004W/G3006F/ G3007U series hearth base accessories. The hearth base accessory shown is optional for this installation. You can install fireplace and cabinet/corner mantel directly on the floor. The corner mantel accessory cannot be installed with the G3000F/G3001U/ G3004W/G3006F/G3007U hearth base. The corner mantel can be paired with the G3008F/ G3009U/G3010F corner hearth base. If mounting fireplace and cabinet or corner mantel to the floor, an optional G3005 Slim Base kit may be installed.

1.Assemble cabinet mantel, hearth base, and trim accessories. Assembly instruc- tions are included with each accessory.

2.When installing blower, install a prop- erly grounded, 120 volt three-prong electrical outlet at fireplace location if an outlet is not there. If possible, lo- cate outlet so cabinet mantel will cover it when installed (see Figure 9).

3.Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Installing Gas Piping to Fireplace Lo- cation, pages 10 and 11.

Electrical

Gas Line

Hearth Gas Line Outlet

Access

Base

Hole

Figure 9 - Placing Hearth Base Accessory Against Wall

For more information, visit www.desatech.com

8

107171

Page 8
Image 8
Desa VSGF33NR Installation Clearances, Conventional Fireplace Installation, Minimum Clearances For Side, Continued