EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the saw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. DD, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
Ampere | Volts | Total Length of | Gauge of |
Rating | | Cord in Feet | Extension Cord |
0-6 | 120 | up to 25 | 18 AWG |
0-6 | 120 | 25-50 | 16 AWG |
0-6 | 120 | 50-100 | 16 AWG |
0-6 | 120 | 100-150 | 14 AWG |
6-10 | 120 | up to 25 | 18 AWG |
6-10 | 120 | 25-50 | 16 AWG |
6-10 | 120 | 50-100 | 14 AWG |
6-10 | 120 | 100-150 | 12 AWG |
10-12 | 120 | up to 25 | 16 AWG |
10-12 | 120 | 25-50 | 16 AWG |
10-12 | 120 | 50-100 | 14 AWG |
10-12 | 120 | 100-150 | 12 AWG |
12-16 | 120 | up to 25 | 14 AWG |
12-16 | 120 | 25-50 | 12 AWG |
12-16 | 120 | GREATER THAN 50 FEET NOT RECOMMENDED |
| | | |
Fig. DD
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
Ampere | Volts | Total Length of | Gauge of |
Rating | | Cord in Feet | Extension Cord |
0-6 | 240 | up to 50 | 18 AWG |
0-6 | 240 | 50-100 | 16 AWG |
0-6 | 240 | 100-200 | 16 AWG |
0-6 | 240 | 200-300 | 14 AWG |
6-10 | 240 | up to 50 | 18 AWG |
6-10 | 240 | 50-100 | 16 AWG |
6-10 | 240 | 100-200 | 14 AWG |
6-10 | 240 | 200-300 | 12 AWG |
10-12 | 240 | up to 50 | 16 AWG |
10-12 | 240 | 50-100 | 16 AWG |
10-12 | 240 | 100-200 | 14 AWG |
10-12 | 240 | 200-300 | 12 AWG |
12-16 | 240 | up to 50 | 14 AWG |
12-16 | 240 | 50-100 | 12 AWG |
12-16 | 240 | GREATER THAN 100 FEET NOT RECOMMENDED |
| | | |
Fig. DD
OPERATING INSTRUCTIONS
FOREWORD
Delta Model 36-600 is a 10" Table Saw designed to give high quality performance with maximum depth of cut capacity up to 3-1/8" (79mm) at 90° and 2-1/8" (54mm) at 45° for clean cutting of standard stock sizes. Delta Model 36-600 includes; basic machine, sturdy steel stand, integral dust chute, a T-Square fence system, T-Slot miter gage, 15 amp motor, on/off switch, cast iron table, 22-1/4" x 38-3/8" extension wings, see-thru blade guard with anti-kickback fingers, convenient up-front blade raising and tilting controls and 10" carbide blade.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR
ACCESSORIES.
