![](/images/new-backgrounds/1315132/31513229x1.webp)
FIG. 17 | FIG. 18 |
| |
| A. |
B.
FIG. 19 | ANGLE “A” |
FIG. 20
|
|
|
|
|
|
|
|
|
|
|
| .62 |
55 |
|
|
|
|
|
|
|
|
|
|
| 31 |
62 |
|
|
|
|
|
|
|
|
|
| 60 | |
35 |
|
|
|
|
|
|
|
|
|
| ||
| 31. |
|
|
|
|
|
|
|
|
|
|
|
| 60 |
|
|
|
|
|
|
|
|
|
| 30 |
| 30 | 65 | 22.5 |
|
|
|
|
|
|
| 22.5 | 65 |
|
|
|
|
|
|
|
|
|
| 25 | ||
|
| 25 | 70 |
|
|
|
|
|
|
| 70 |
|
|
|
|
|
|
|
|
|
| 75 | 20 |
| |
|
|
| 20 | 75 |
|
|
|
|
|
| ||
|
|
|
|
|
|
| 80 | 15 |
|
| ||
|
|
|
| 15 | 851 | 2 | 2 | 901 |
|
| ||
|
|
|
| 10 |
|
|
| |||||
|
|
|
|
|
| 1 | 1 |
|
|
|
|
|
|
|
|
|
| 5 |
|
| 0 |
|
|
|
|
MITER
SCALE
FIG. 21
V1
KERF
PLATE
MITER ARM
CENTER MARK ON VERNIER SCALE ALIGNS WITH DESIRED WHOLE ANGLE ON MITER SCALE (24° RIGHT MITER)
V2
1/4° VERNIER MARK ALIGNS WITH CLOSET WHOLE DEGREE MARK ON MITER SCALE (24 1/4° RIGHT MITER)
FIG. 22
Note: If the cut must be made somewhere other than
1" from the end of the molding: cut off the molding at 90° approx. 1" longer than your final length then make the miter cut as described above.
Right side
1.Position molding with bottom of the molding against the base of the saw
2.Miter left 45°
3.Save the right side of cut
A third method of making the cut necessary is to make a zero degree miter, 45 degree bevel cut. Your saw can cut a bevel 7 7/8" wide.
CUTTING BASE MOLDING LAYING FLAT AND USING THE BEVEL FEATURE
•All cuts made with the saw set at 45° bevel and 0 miter
•All cuts made with back of molding laying flat on the
saw | as shown in figures 23 and 24 |
INSIDE CORNER:
Left side
1.Position molding with top of molding against the fence
2.Save left side of cut
Right side
1.Position molding with bottom of the molding against the fence
2.Save left side of cut
OUTSIDE CORNER:
Left side
1.Position molding with bottom of the molding against the fence
2.Save right side of cut
Right side
1.Position molding with top of molding against the fence
2.Save right side of cut
CUTTING CROWN MOLDING
Your miter saw is better suited to the task of cutting crown molding than any tool made. In order to fit properly, crown molding must be compound mitered with extreme accuracy.
The two flat surfaces on a given piece of crown molding are at angles that, when added together, equal exactly 90 degrees. Most, but not all, crown molding has a top rear angle (the section that fits flat against the ceiling) of 52 degrees and a bottom rear angle (the part that fits flat against the wall) of 38 degrees.
Your miter saw has special
31.62degrees left and right for cutting crown molding at the proper angle. There is also a mark on the Bevel scale at 33.85 degrees.
The chart on this page gives the proper settings for cutting crown molding. (The numbers for the miter and bevel settings are very precise and are not easy to
English
11