Chapter 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Product Overview

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bottom Panel

 

 

Wall-Mounting Placement

 

 

 

 

 

 

 

 

 

 

 

 

 

The Router has two wall-mount slots on its bottom

 

 

 

 

 

 

panel. The distance

 

between the slots is 152 mm

 

 

 

 

 

 

(6 inches).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Two screws are needed to mount the Router.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Suggested Mounting Hardware

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-3.0 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-5 mm

 

1-1.5 mm

 

 

 

 

 

 

 

 

 

2.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reset  The Reset button is located on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

††Note: Mounting hardware illustrations are not

 

 

right side of the product label. There are two

 

 

 

 

 

 

true to scale.

 

 

 

 

 

 

 

 

 

 

 

ways to reset the Router to its factory defaults.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Either press and hold the Reset button for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Linksys is not responsible for damages

 

 

approximately five seconds, or restore the

 

 

 

 

 

 

 

 

 

defaults from the Administration > Factory

 

 

 

 

 

 

 

incurred by insecure wall-mounting hardware.

 

 

Defaults screen of the Router’s webbased

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

utility.

 

 

Follow these instructions:

 

 

 

Horizontal Placement

 

 

1. Determine where you want to mount the Router. Make

 

 

sure that the wall you use is smooth, flat, dry, and

The Router has four rubber feet on its bottom panel. Place

 

 

sturdy. Also make sure the location is within reach of

 

 

an electrical outlet.

 

 

 

the Router on a level surface near an electrical outlet.

 

 

 

 

 

 

 

2. Drill two holes into the wall. Make sure the holes are

 

 

 

 

 

 

 

 

 

 

 

 

152 mm (6 inches) apart.

 

 

 

 

 

 

 

 

 

3. Insert a screw into each hole and leave 3 mm

 

 

 

 

 

 

(0.12 inches) of its head exposed.

 

 

 

 

 

 

4. Maneuver the Router so the wall-mount slots line up

 

 

 

 

 

 

with the two screws.

 

 

 

 

 

 

 

 

 

5. Place the wall-mount slots over the screws and slide

 

 

 

 

 

 

the Router down until the screws fit snugly into the

 

 

 

 

 

 

wall-mount slots.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

152 mm

Print this page at 100% size.

Cut along the dotted line, and place on the wall to drill precise spacing.

Wall-Mounting Template

Wireless-N Broadband Router with Storage Link

2

Page 6
Image 6
DeWalt WRT160NL manual Bottom Panel, Horizontal Placement