Amplifier Installation

Choosing Mounting Locations

The location of your amplifier will depend on several important issues.. Due to the low profile size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.. Always mount the amplifier in a place that protects the amplifier from the elements.. In addition, mount the amplifier on a stable, flat surface..

NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown.

WARNING! Do not mount any amplifier in the engine compart- ment. Amplifiers are not designed to endure the harsh envi- ronment of the exterior elements.

Passenger Compartment

If you are going to mount the amplifier in the passenger compart- ment, make sure you have adequate room for ventilation.. The amplifi- ers have been designed to make under-seat mounting possible.. When mounting your amplifier under a seat or similar area, keep a minimum of 1” of clearance around the amplifier for adequate cooling..

Trunk Compartment

Mounting your amplifier in the trunk provides excellent performance as long as you do not restrict the airflow around the heatsink of the

amplifier.. For optimal results, mount the amplifier with as much clear- ance as possible.. This type of mounting will yield the best cooling due to the convection effect of the amplifier chassis..

General Precautions and Installation Tips

WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle..

Disconnect the vehicle’s ground wire at the battery before making or breaking connections to the audio system’s power supply terminals..

Do not use this amplifier unmounted.. Failing to securely mount the amplifier can result in damage or injury, particularly in the event of an accident.. An unmounted amplifier becomes a dangerous projectile in the event of a crash.. Never mount the amplifier where it might get wet.. Mount the amplifier so the wire connections will not be pulled.. Route the wires where they will not be scraped, pinched or damaged in any fashion..

The +12V power supply wire must be fused as close as possible to the battery terminal, ideally within 12”.. Use the recommended fuse size or circuit breaker listed in the Power Connections section of this manual..

If you need to replace the fuse plugged into the side of the amplifier, replace the fuse with the same size and type fuse that came with the amplifier.. If you are not sure as to the correct value, refer to the Power Connections section of this manual for details.. Using a higher current fuse may result in damage to the amplifier that is not covered under warranty..

© 2008 Directed Electronics. All rights reserved.

12

Page 13
Image 13
Directed Audio XTR5004, XTR2504 owner manual Choosing Mounting Locations, Passenger Compartment, Trunk Compartment

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.