slight distortion and turn the level control back slightly for an undistorted output.. Depending on your system, the midrange and tweeter output may be on the same output channels..

6.Turn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output.. Depending on your system the midrange and tweeter output may be on the same output channels..

7.Fine-tune the output level between midrange and tweeters.. Refer to the Internal Crossover Configuration section of this manual for detailed instructions..

8.Repeat Steps 5-7 for the rear speakers.. If you do not have rear speakers continue to Step 10..

9.Set levels between the front and rear midrange and tweeters for optimum front/rear balance..

10.Turn up the level control corresponding to the woofer output until you hear slight distortion and turn back the level control slightly for an undistorted output..

11.Fine-tune the output level between satellite speakers and the woofers.. Refer to the Internal Crossover Configuration section of this manual for detailed instructions..

12.Enjoy your awesome Orion sound system..

Amplifier Visual Troubleshooting

Your new XTR amplifier has three indicator lights (LED’s) mounted on the top plate of the amplifier as seen in the next figure.. These lights are very useful in trouble shooting possible amplifier problems and issues..

Power LED: This LED lights up green when the amplifier is turned on.. This represents normal operation if the Protection and Thermal LED’s next to it are off..

Protection LED: This LED lights up red if the amplifier goes into protection.. Below is a description of reasons the amplifier could engage the protection circuit.. The protection indications will self reset once the condition has been fixed..

•Short: Speaker wires pinched or shorted together or to ground (frame of vehicle)..

•Overcurrent: Check for possible speaker issue(s) or speaker wiring pinched in a door or other metal.. Make sure speaker(s) load is not below the minimum impedance load..

•DC Offset: This can happen if the installation inadvertently connects the power wire to the speaker input(s).. This can also happen if the amplifier has an internal problem..

•Undervoltage: Vehicle charging system is not supplying enough voltage to the amplifier.. This can also occur if you use too small a gauge wire or the terminals connecting the amplifier power to the electrical system are dirty or corroded..

•Overvoltage: Vehicle charging system is supplying too much voltage or over the amplifiers rated DC input.. Usually this occurs when there is a problem with the electrical system.. Turn off the headunit when jump-starting the car..

© 2008 Directed Electronics. All rights reserved.

16

Page 16 Page 18
Page 17
Image 17
Directed Audio XTR5004, XTR2504 owner manual Amplifier Visual Troubleshooting
Page 16 Page 18

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.
Top Page Image Contents