Care And Maintenance | Dixon ZTR 5022, ZTR 5017 instruction

CARE AND MAINTENANCE

PARKING BRAKE CABLE ADJUSTMENT:

Make necessary adjustments to the T-Box to Hydrostat belt, as shown on page 32.

Position parking brake lever in the off or disengaged position.

This will allow the belt idler used on the engine to T-box to swing fully and apply tension to the belt.

At this time, check that the cable has approximately 1-1/2 to 2 inches of free play.

If adjustment is required, turn the lock nut illustrated below to achieve a recommended 1-1/2 to 2 inches of free play.

ADJUST HERE FOR

PROPER FREE PLAY OF

CABLE WITH BRAKE

LEVER OFF

NOTE: Cable must have the recommended 1-1/2 to 2 inches of free play with parking brake released or drive belt may slip, causing loss of power.

Page 36

Image 36

Dixon ZTR 5022, ZTR 5017 manual Care And Maintenance, Parking Brake Cable Adjustment

Contents

5000 SERIES 1999 Operators Manual IMPORTANT - READ CAREFULLY INDEX 5000 Series SAFETY The most common causes of injury to the operator or bystanderread and understand this manual to prevent injuries RIDING LAWNMOWERS, IF IMPROPERLY OPERATED SAFETY SYMBOLS DangerFollow recommended safety precautions and safe operating practices Safety Alert Symbol SAFETY Failure to observe the following safety instructions could result inThis cutting mower is capable of amputating hands & feet and throwing objects SLOPE OPERATION CHILDREN SERVICE SEE DEALER FOR DETAILS DIXON LIMITED WARRANTY POLICY -- HYDRO-GEAR MODELS DIXON LIMITED WARRANTY POLICY -- ESTATE MODELS WARRANTY SPECIFICATIONS Model ZTR 5020 CHASSIS 11 GA - rectangular tube SEAT ADJUSTMENT INSTRUCTIONS 5000 Series Models 1. Grasp seat slide adjuster and move it into adjustment position2. Slide seat forward or backward 3. Release seat slide adjuster CONTROLS PARKING BRAKE CAUTION Engage parking brake before starting engineTO SET PARKING BRAKE HYDRO-GEAR DRIVE SYSTEM TO GO BACKWARD TURNING BRAKINGCHOKE CONTROL LEVER THROTTLE CONTROL LEVER BLADE DRIVE CIRCUIT BREAKERMOWER DECK CUT HEIGHT LIFT LEVER OPERATION INSTRUCTIONS BEFORE OPERATING MOWERTOWING TESTING OF SAFETY INTERLOCK SYSTEMS If Any Safety Check FAILS Do Not Operate The Mower untilthe system has been checked and repaired by an Authorized Dixon ZTR Dealer STARTING INSTRUCTIONS Cold Engine STARTING INSTRUCTIONS Engine has been operated MOWING WITH A MULCHING ATTACHMENT MOWING WITH A GRASS CATCHER ATTACHMENT 6. Maintain Sharp Blades Throughout The Cutting Season Besurethatdeflectorisproperlyinstalledonthe dischargechute SIDE DISCHARGE OF THE CLIPPINGSGRASS HEIGHT SUGGESTIONS 5. Maintain Sharp Blades Throughout The Cutting Season DECK ROLLERS 60 Deck CARE AND MAINTENANCE MAINTENANCE SCHEDULEBefore performing any maintenance, shut off engine OFF-SEASON BATTERY STORAGE MOWER BLADE MAINTENANCE BELT TENSION ENGINE TO MOWER DECK BELTBELT SERVICE INTERVALS FUEL SHUT OFF VALVELUBRICATION LOCATIONS REAR WHEELS WHEEL REVERSAL CHANGING THE ENGINE OIL PROTECT YOUR INVESTMENTPLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS PROTECT YOUR ENVIRONMENT MOWER DECK REMOVAL MOWER DECK LEVELING PROCEDURE T-BOX TO HYDROSTAT BELT ADJUSTMENT PARKING BRAKE CABLE ADJUSTMENT NEUTRAL ADJUSTMENT FORWARD TRAVEL SPEED ADJUSTMENT PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT A. AIR GAP ADJUSTMENTB. OHMS TEST HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICE OIL REQUIREMENTSOIL FILTER P/N 7252- IMPORTANT 3. Put fresh oil in reservoir. Fill reservoir to the full mark CLEANING THE MOWER WARRANTYPARTS/SERVICE WHEELS AND TIRES STANDARD SERVICE PARTS LIST 42 DECK50 DECK 60 DECK KOHLER AND BRIGGS & STRATTON AIR AND OIL FILTER PART NUMBERS TROUBLESHOOTING MOWER CUT QUALITYSITUATION CAUSES DRIVE SYSTEM ELECTRICAL SYSTEM Page OWNER INFORMATION MOWER MODEL NUMBERPURCHASED FROM MOWER SERIAL NUMBER Dixon and ZTR are registered trademarks of Dixon Industries, Inc5000Series