Dolby Laboratories DP569 Appendix D Error Messages

Model DP569 User’s Manual

D–1

Appendix D

Error Messages

This appendix lists possible error messages that may be generated by the DP569. In

each case a description of possible setup conflicts are given that may have caused the

error. When a conflict occurs the parameter that caused the conflict will not be

updated but returned to its original value once the error message has been displayed.

NOT VALID: CHECK

DATA RATE

• A new Channel Mode has been selected but is not supported for the current

Data Rate.

• Internal 32 kHz has been selected as the Clock Source, the current Output

Mode is Pro 16-bit and the current Data Rate is 448 kbps or greater.

NOT VALID: CHECK

CHANNEL MODE

• A new Data Rate has been selected but is not supported for the current

Channel Mode setting.

• Main Srv Karaoke has been selected as the Bitstream Mode and the current

Channel Mode is 1+1 Dual Mono or 1/0 Mono; or Assc Voice Over has

been selected and the current Channel Mode is not 1/0 Mono.

• The LFE Channel has been Enabled and the current Channel Mode is 1+1

Dual Mono, 1/0 Mono, or 2/0 Stereo.

NOT VALID: CHECK

BITSTREAM MODE

• Either 1+1 Dual Mono or 1/0 Mono has been selected as the Channel Mode

and the current Bitstream Mode is Main Srv Karaoke. Or any selection

other than 1/0 Mono has been made and the current Bitstream Mode is Assc

Voice Over.

NOT VALID: CHECK

LFE MODE

• 1+1 Dual Mono, 1/0 Mono, or 2/0 Stereo has been selected as the Channel

Mode and the LFE Channel is Enabled.

Contents

Main Dolby Laboratories, Inc. Table of Contents Page Page Page List of Figures List of Tables Regulatory Notices and Fuse Information FCC Canada UL UK EU Fuse Information Page Chapter 1 Introduction Page Chapter 2 Setting Up 2.1 Unpacking 2.2 System Considerations 2.2.1 Jumpers 2.2.2 Digital Input and Output 2.3 Front Panel 2.3.1 Front-Panel Interface 2.3.2 Contrast Adjust 2.3.3 Preset Buttons 2.4 Status Menu 2.5 Setup Menu 2.5.1 Selecting Parameters 2.5.2 Entering Text 2.6 Front-Panel Indicators 2.6.1 Digital Input Status LEDs 2.6.2 Fault, Error, Test, Ref In, Remote, and Timecode LEDs 2.6.3 Channel Activity LEDs 2.6.4 Remote Connector Chapter 3 Applications 3.1 Digital Television Broadcasting 3.1.1 Basic Integration with an MPEG Encoder or Multiplexer MUXDP569 3.1.2 Integration within a Dolby E System MUXDP569 DP572 3.1.3 Metadata Reversion 3.1.4 Coding Delay and Audio/Video Synchronization 3.1.5 Alarms and Monitoring 3.1.6 Quick Start for Digital Television Broadcasting 3.2 DVD Authoring 3.2.1 Overview 3.2.2 Quick Start for DVD Authoring Page Page Chapter 4 Front-Panel Menus 4.1 Status Menu 4.2 Setup Menu 4.2.1 Operating Mode 4.2.2 Metadata Control 4.2.3 Metadata Params 4.2.4 User Presets 4.2.5 I/O Control Page Page 4.2.6 System Settings Page Chapter 5 DolbyRemote 5.1 DolbyRemote Overview 5.2 Installation 5.2.1 PC System Requirements 5.2.2 Software Installation 5.2.3 Serial Cable Installation 5.2.4 DP569 Setup 5.3 Starting DolbyRemote 5.3.1 Device Type 5.3.2 Communications Page 5.3.3 Adding or Removing Additional Devices 5.4 General Operation 5.4.1 Saving and Restoring Configurations 5.4.2 Exporting Configurations 5.5 Common Setup Problems 5.6 Display Overview 5.6.1 Audio Service Parameters Page Page 5.6.6 Presets 5.6.7 Timecode Parameters Page Model DP569 Users Manual 6-1 Chapter 6 Specifications Figure 6-2 DP569 Rear Panel 6.1 System Block Diagram Figure 6-1 System Block Diagram 6.2 Connections Page 6.2.5 Metadata Serial Port 9-pin female D-connector, electrical specifications per SMPTE 207M 6.2.6 Rear Panel Remote Control Serial Port (Remote) 9-pin female D-connector per SMPTE 207M 6.2.7 Front Panel Remote Control Serial Port (Remote) 8-pin female mini-DIN connector, electrical specifications per EIA RS-232 6.2.8 General Purpose Control Input Port (GPI/O In) 9-pin female D-connector, 5 V CMOS input levels (active low) 6.3 Mechanical Specifications 6.4 Environmental Specifications Page Appendix A Metadata A.1 Metadata Overview Page Page A.2 Dialogue Level Page A.3 Dynamic Range Control A.3.1 Line Mode A.3.2 RF Mode A.3.3 Dynamic Range Control Profiles Input Level Boost Null Band Cut Early A.4 Downmixing Page A.5 Parameter Definitions A.5.1 Universal Parameters Page Page Page Page Page Page A.5.2 Extended Bitstream Information Parameters Page Page A.6 Metadata Combinations Page Page Appendix B SMPTE Time Stamp Page Model DP569 Users Manual C1 Appendix C Factory Default Presets Model DP569 Users Manual Factory Default Presets C2 Appendix D Error Messages