Manuals
/
Brands
/
Home Audio
/
Stereo Amplifier
/
Dynacord
/
Home Audio
/
Stereo Amplifier
Dynacord
DSA 8405, DSA 8410, DSA 8805 owner manual
1
1
40
40
Download
40 pages, 2.89 Mb
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
Contents
Main
Page
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SERVICE INSTRUCTIONS
WEEE RECYCLING/DISPOSAL INSTRUCTIONS
8.
.
1 Introduction
Page
2 Installation
2.1 Controls, Indicators and Connections
Owners Manual 7
2.2 Operating Voltage
Table 2.1: Operating Voltage
Mains Operation and Resulting Temperature
2.3 Mains Switch
2.4 Mounting
Page
Page
2.7 Selecting the Mode of Output (OUTPUT)
Owners Manual 11
70 V Mode
Illustration 2.7: CH 1 in 100 V mode
100 V Mode
2.8 Variable Load Drive (VLD)
Illustration 2.6: CH 1 in 70 V mode
12 Owners Manual
2.9 Power on delay
Table 2.3: Maximum Output Power (VLD deactivated)
Table 2.4: Maximum Output Power (VLD activated)
CAUTION: The setting of ON DELAY is ignored if a Remote Control Module is assembled.
Page
14 Owners Manual
3 Operation
3.1 Volume Control
3.2 Indications
PROTECT
MUTE
4 Options
4.1 RCM-810
System Description and Features
16 Owners Manual
Controls and Connections
All RCM-810 parameters configured via IRIS-Net are discarded when pressing the INIT button.
Table 4.1: Factory Settings of RCM-810
Each address may exist only once in a system. Otherwise, network conflicts may arise.
Owners Manual 17
NOTE: The data rate of the CAN bus is preset to 10 kbit/s.
Table 4.3: Transfer rate and bus length
The maximally allowable current at the +5V output is 200 mA.
Illustration 4.2: Pin-assignment of CAN jack and CAN plug
Page
WICHTIGE SICHERHEITSHINWEISE
WICHTIGE SERVICEHINWEISE
Hinweise zur Entsorgung/Wiederverwendung gem WEEE
9.
NOTE: SAFETY COMPONENT (MUST BE REPLACED BY ORIGINAL PART)
1 Einfhrung
1.1 Auspacken und berprfen
Versenden Sie die Endstufe nie ohne das original Verpackungsmaterial.
1.2 Lieferumfang und Garantie
1.3 Verantwortung des Betreibers
2 Installation
2.1 Bedienelemente, Anzeigen und Anschlsse
22 Bedienungsanleitung
2.2 Betriebsspannung
Abbildung 2.1: Befestigung der Endstufe bei Rackeinbau
Netzbetrieb und Wrmeentwicklung in der Endstufe
2.3 Netzschalter
2.4 Einbau
Page
Page
2.7 Wahl des Ausgangs-Modus (OUTPUT)
26 Bedienungsanleitung
70 V-Modus
Abbildung 2.8: CH 1 im 100 V-Modus
100 V-Modus
2.8 Variable Load Drive (VLD)
Abbildung 2.7: CH 1 im 70 V Modus
Bedienungsanleitung 27
2.9 Einschaltverzgerung
Tabelle 2.3: Maximale Ausgangsleistung je Kanal (VLD deaktiviert)
Tabelle 2.4: Maximale Ausgangsleistung je Kanal (VLD aktiviert)
ACHTUNG: Die ON DELAY Einstellung wird ignoriert, wenn ein Remote Control Module eingebaut ist.
Page
Bedienungsanleitung 29
3 Betrieb
3.1 Eingangspegel-Regler
3.2 Anzeigen
PROTECT
MUTE
4 Optionen
Abbildung 4.1: Bedienelemente und Anschlsse des RCM-810
4.1 RCM-810
Systembeschreibung
Bedienelemente und Anschlsse
Jede Adresse darf im System nur einmal vorkommen, da es sonst zu Netzwerk-Konflik- ten kommt.
32 Bedienungsanleitung
HINWEIS: Die Datenrate ist auf 10 kbit/s voreingestellt.
Tabelle 4.3: Datenrate und Buslnge in CAN-Netzwerken
Der maximale Gesamtstrom am Ausgang +5V betrgt 200 mA.
Abbildung 4.2: Belegung der CAN-Buchse und des CAN-Steckers
Specifications/Technische Daten
DSA 8405
DSA 8410
DSA 8805
5.1 Mains Operation & Resulting Temperature