4 universal LPG installation electrolux integrated barbecue
Universal LPG installation
Preparing the unit for Universal LPG installation. This barbecue is supplied set up for Natural Gas and is labelled accordingly. A Universal LPG conversion Kit is included to enable conversion to Universal LPG.
NOTE #ONVERSIONåOFåTHISåUNITåTOå5NIVERSALå,0'åMUSTåBEåCARRIEDå out by a qualified licensed person and a Certificate of Compliance must be issued to the owner on completion of the installation and conversion.
The required components for conversion have been supplied. The components are:
så | (OSEåANDåREGULATORåASSEMBLY | |
så | 3MALLåPLASTICåBAGåCONTAININGååBRASSåINJECTORS | |
så | å5NIVERSALå,0'åSTICKER | |
så | åDATAåPLATEåLABEL | |
så | )NSTRUCTIONåSHEET | |
så | åTESTåPOINTåADAPTOR | |
så | åSEALINGåWASHER | |
1. | Change the injectors | |
å | så | 2EMOVEåTHEåFRONTåCOVER |
å | så | 2ELEASEåTHEåBURNERåRETAINERåCLIPåASåSHOWNå |
remove spring clip by rotating over burner tube end
front cover
åså 5NSCREWåANDåREPLACEåTHEååINJECTORåNIPPLESåLOCATEDå in the end of each tube feeding the burners. The Universal LPG injectors have a 0.95mm diameter orifice in them. They appear substantially smaller than the Natural Gas injectors.
LPG injector
2. Adjust the turndown setting on the valve
å så )FålTTED åREMOVEåTHEåKNOBSåFROMåTHEåVALVES
åså 2EMOVEåRUBBERåGROMMETSåFROMåCONTROLåPANELåHOLES
For non flame failure valve adjust the turndown screw fully clockwise on each of the 4 valves using a small flat blade screwdriver. The valve is now set correctly for LPG operation (see diagram).
turndown screw for
If flame failure fitted the turn down screw will need to be adjusted after unit is installed, and unit is ready for testing. This is done using a thin flat blade screw driver inserted through hole in centre of shaft spindle (see diagram).
if flame failure valve fitted,
turn down screw inside shaft with a small
åså &OLLOWINGåCONNECTIONåOFåGASåASåPERåSTEPSå åLIGHTå all burners and one at a time set the burner to the lowest setting and check burner flame. Adjust turn down screw clockwise to achieve a small steady flame.
3.Connect the test point adaptor to the barbecue gas inlet
å så &ITåTHEåTESTåPOINTåADAPTORåENSURINGåTHEåBLUEåSEALINGå washer is in place and the arrow is pointing in the direction of gas flow. Do not
4.Connect the hose to the test point adaptor
åså !PPLYåTHREADåTAPEåORåSEALANTåTOåTHEåMALEåTHREADåONå
the hose and screw into the test point adaptor.
barbecue gas inlet
sealing washer
test point adaptor – ensure arrow is pointing in the right direction
hose with tapered thread
– thread tape required
å | så | 2EFASTENåTHEåCLIPåTOåRETAINåTHEåTUBEåINåTHEåBURNERå | 5. | Replace the ‘gas type’ sticker |
å | så ,OCATEåTHEå@.ATURALå'ASåSTICKERåLOCATEDåONåTHEå | |||
|
| Do not over tighten or distort supply tube. |
| barbecue gas inlet and remove it. Put the Universal |
å | så | &ITåTHEåFRONTåCOVERåBACKåONåANDåFASTENåSCREWS |
| LPG sticker in its place. |
