Connecting the dishwasher | Electrolux FAVORIT 44080 i guide

Connecting the dishwasher

Connecting to the water supply

•The dishwasher can be connected to cold and hot water supplies up to max. 60°C.

•The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

	Lowest permitted water pressure:	Consult your plumber if the water pres-
	1 bar (=10 N/cm2 =100 kPa)	sure is less than 1 bar.

	Highest permitted water pressure:	If the water pressure is greater than 10
	Highest permitted water pressure:	bar, a pressure reduction valve must be
	10 bar (=100 N/cm2 =1 MPa)	bar, a pressure reduction valve must be
	10 bar (=100 N/cm2 =1 MPa)	used (available from your dealer).
		used (available from your dealer).

Connecting the inlet hose

1 The water inlet hose must not be kinked, crushed or entangled when it is being connected.

Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic or a metal nut:

–Only tighten the nut hand tight.

Then do a visual check for water tightness. (Make sure that the tap is not dripping.)

3 So that access to the tap in the kitchen is not restricted by the use of the dishwasher, we recommend installing an additional tap, or fitting a T-branch to the existing tap.

If you need a longer water inlet hose than that supplied, the following VDE-approved complete hose sets are to be used. These are available from your local service centre.

34

Image 34

Electrolux FAVORIT 44080 i manual Connecting the dishwasher, Connecting to the water supply, Permitted water pressure

Contents

Favorit 44080 Following symbols are used in the text Dear Customer Contents Child Safety SafetyPrior to using for the first time General Safety Diagram of Appliance Control Panel Control indicators have the following meanings Setting manually Prior to Using for the First TimeSetting the Water Softener Setting electronically Setting Only when using the dishwasher for the first time Adding dishwasher Salt Filling Up with Rinse Aid Setting the Amount of Rinse Aid Required Daily use Loading cutlery and dishes Loading cutlery Pots, Pans, Large Plates Cups, Glasses, Coffee Service Adding Detergent Adjusting the Height of the Upper BasketRaising / Lowering the upper bas- ket Concentrated detergents Detergent tablets If you do not want to use 3in1 products any more Using 3in1 detergentsIf you want to use 3in1 products If you want to use 4in1 products Selecting the dishwashing cycle Cycle Table Suitable Type Selecting a programme Cancelling the wash programme Interrupting or Cancelling a dishwashing cycleSetting the Delay Timer Starting a Dishwashing Cycle Cancelling the delay timer Switching Off the dishwasherTo change the time delay Removing the Dishes Care and cleaning Cleaning the filters Cleaning the spray arm jets Upper basket spray arm Bottom spray arm What to do if Remedying small malfunctions Indicator for the end Dishwashing cycle is Dishes do not dry and are not shining If the Dishwashing Results are not SatisfactoryDishes are still dirty There are dried water drops on the glasses and dishes Packaging material DisposalOld appliance Technical Data Example loading arrangements Full load Half loadPage Installation and connection instructions Safety Information for the Installation Installing the Dishwasher Dishwashers That Can be Integrated Connecting the inlet hose Connecting the dishwasherConnecting to the water supply Permitted water pressure Water drainage Anti-flood system Changing a fuse Electrical ConnectionGreen and Yellow Earth BlueNeutral BrownLive Connecting systems Warranty conditions Great Britain 0870 5 929 Customer Care For general enquiries concerning AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG