Electrolux FMV156DBE Door Replacementdoor Assembly Removal, Door Assembly RE-INSTALL

After adjustment, check the following.

1.In and out play of door remains less than 0.5mm when in the latched position. First check upper position of latch hook, pushing and pulling upper portion of door toward the oven face.Then check lower portion of the latch hook, pushing and pulling lower portion of the door toward the oven face. Both results (play in the door) should be less than 0.5mm.

2.The door sensing switch and primary interlock switch interrupt the circuit before the door can be opened.

3.Monitor switch contacts close when door is opened.

4.Re-install outer case and check for microwave leakage around door with an approved microwave survey meter. (Refer to Microwave Measurement Procedure.)

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

	Latch heads
	Latch hook
	Door sensing
Door	switch
	Monitor switch

Primary interlock switch

Figure C-1. Latch Switch Adjustments

		DOOR REPLACEMENTDOOR ASSEMBLY REMOVAL
1.	Disconnect the power supply cord.		After any servicing, make sure of the following :
2.	Open the door and block it open.		1.	Door latch heads smoothly catch latch hook through
3.	To discharge the high voltage capacitor, wait for 60			latch holes and that latch head goes through center of
	seconds.			latch hole.
4. Remove the three (3) screws holding the hood exhaust			2. Deviation of door alignment from horizontal line of cavity
	louver to the oven cavity front face plate.			face plate is to be less than 1.0mm.
5.	Remove the hood exhaust louver from the oven cavity		3.	Door is positioned with its face pressed toward cavity
	by pushing the right and left tabs of the hood exhaust			face plate.
	louver. (Refer to the procedure of "hood exhaust		4.	Re-install outer case and check for microwave leakage
	louver REMOVAL".)			around door with an approved microwave survey meter.
6.	Insert a putty knife (thickness of about 0.5mm) into the			(Refer to Microwave Measurement Procedure.)
	gap	A between the door stopper and the choke cover	Note: The door on a microwave oven is designed to
	as shown in Figure C-3 to free engaging parts.
				act as an electronic seal preventing the leakage
7.	Lift up the door stopper.
				of microwave energy from oven cavity during
8.	Now, the door stopper is free from the door assembly.
				cook cycle. This function does not require that
9.	Lift up the door assembly to release the upper and lower
				door be air-tight, moisture (condensation)-tight
	door hinge pins from the upper and lower oven hinges.
				or light-tight.Therefore, occasional appearance
10.Now, the door assembly is free.
				of moisture, light or sensing of gentle warm air
Note:		When the individual parts are replaced, refer to		movement around oven door is not abnormal
		"Door Disassembly".		and do not of themselves indicate a leakage of
DOOR ASSEMBLY RE-INSTALL				microwave energy from oven cavity.
1.	On re-installing door, insert the lower oven hinge to lower				Tab	Hood Exhaust Louver
	door hinge pin.			Upper Door
2.	Insert the upper oven hinge to the upper door hinge			Hige Pin
	pin.				Upper	Tab
3.	Shut the door (close the contacts of interlock
				RE-INSTALL	Oven
	switches).
					Hige
4.	Make sure upper and lower oven hinges are inserted			Door assembly
	into the upper an lower door hinge pins.
5.	Make sure the door is parallel with oven face lines (left
	and upper side lines) and door latch heads pass through				Lower
	latch holes correctly.
					Oven Hige
6.	Re-install the door stopper to the door assembly.
7.	Re-install the hood exhaust louver to the oven cavity
	front face plate with the three (3) screws.			Latch	Lower Door
Note:		After any service to the door;		Heads	Hige Pin	Door Stopper
(A)	Make sure that door sensing switch and primary
					RE-INSTALL
	interlock switch are operating properly. (Refer to
				Figure C-2. Door Replacement and adjustment
	chapter "Test Procedures".)

(B)An approved microwave survey meter should be used to assure compliance with proper microwave radiation emission limitation standards.

35