Electrolux FMV156DBE service manual Operation, Description of Operating Sequence

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

OPERATION

DESCRIPTION OF OPERATING SEQUENCE

The following is a description of component functions dur- ing oven operation.

OFF CONDITION

Closing the door activates the door sensing switch and secondary interlock switch. (In this condition, the monitor switch contacts are opened.)

When oven is plugged in, 120 volts A.C. is supplied to the control unit. (Figure O-1).

1.The display will show "WELCOME, PRESS CLEAR AND PRESS CLOCK".

To set any program or set the clock, you must first touch the STOP/CLEAR pad. The display will clear, and " : " will appear .

COOKING CONDITION

Program desired cooking time touching the NUMBER pads. When the START pad is touched, the following operations occur:

1.The contacts of relays are closed and components connected to the relays are turned on as follows.

(For details, refer to Figure O-2)

RELAY	CONNECTED COMPONENTS
RY1	Oven lamp / Fan motor / Stirrer motor
RY2	Power transformer
RY3	Turntable motor
RY4	Hood fan motor

2.120 volts A.C. is supplied to the primary winding of the power transformer and is converted to about 3.3 volts A.C. output on the filament winding, and approximately 2000 volts A.C. on the high voltage winding.

3.The filament winding voltage heats the magnetron filament and the H.V. winding voltage is sent to a voltage doubler circuit.

4.The microwave energy produced by the magnetron is channelled through the waveguide into the cavity feed- box, and then into the cavity where the food is placed to be cooked.

5.Upon completion of the cooking time, the power transformer, oven lamp, etc. are turned off, and the generation of microwave energy is stopped. The oven will revert to the OFF condition.

6.When the door is opened during a cook cycle, monitor switch, door sensing switch, primary interlock switch, and secondary interlock relay are activated with the following results. The circuits to the stirrer motor, the cooling fan motor, the turntable motor, and the high voltage components are de-energized, and the digital read-out displays the time still remaining in the cook cycle when the door was opened.

7.The monitor switch is electrically monitoring the

of the primary interlock switch, and door sensing switch is mechanically associated with the door so that it will function in the following sequence.

(1)When the door opens from a closed position, the secondary interlock relay, door sensing switch, and primary interlock switch open their contacts, and then the monitor switch contacts close.

(2)When the door is closed from the open position,

the	monitor switch contacts open first. Then the
contacts	of the primary interlock switch and door
sensing	switch close. And contacts of

the relay (RY1) open.

If the primary interlock switch and secondary interlock relay (RY2) fail with the contacts closed when the door is opened, the closing of the monitor switch contacts will form a short circuit through the monitor fuse, primary interlock switch, relay (RY1) and secondary interlock relay (RY2), causing the monitor fuse to blow.

POWER LEVEL P-0 TO P-90 COOKING

When Variable Cooking Power is programmed, the 120 volts A.C. is supplied to the power transformer intermittently through the contacts of relay (RY2) which is operated by the control unit within an interval second time base. Microwave power operation is as follows:

VARI-MODE	ON TIME	OFF TIME
Power 10(P-HI)	32 sec.	0 sec.
(100% power)
Power 9(P-90)	30 sec.	2 sec.
(approx. 90% power)
Power 8(P-80)	26 sec.	6 sec.
(approx. 80% power)
Power 7(P-70)	24 sec.	8 sec.
(approx. 70% power)
Power 6(P-60)	22 sec.	0 sec.
(approx. 60% power)
Power 5(P-50)	18 sec.	4 sec.
(approx. 50% power)
Power 4(P-40)	16 sec.	6 sec.
(approx. 40% power)
Power 3(P-30)	12 sec.	20 sec.
(approx. 30% power)
Power 2(P-20)	8 sec.	24 sec.
(approx. 20% power)
Power 1(P-10)	6 sec.	26 sec.
(approx. 10% power)
Power 0(P-0)	0 sec.	32 sec.
(0% power)

Note: The ON/OFF time ratio does not correspond with the percentage of microwave power, because approx. 2 seconds are needed for heating of the magnetron