RANGE TOP CONVERSION TO “LP”

Models 1955 & 1956

All our ranges are factory set to burn natural gas unless “LP” is specified. To use the range on “LP” gas, please do the following:

Order an “LP” kit from the factory. $35 UPS included.

Burner

Large

Medium

Small

Nat. Gas

#50 (1.75 mm)

#55 (1.32 mm)

#57 (1.09 mm)

LP/Propane

#64 (.91 mm)

#65 (.89 mm)

#70 (.71 mm)

Store natural gas spuds so they are available for future conversions.

Installation of “LP” Spuds

Apply masking tape to the end of a 7 mm nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out, set gas orifice spud aside.

Gas orifice spuds are stamped with a number on the side. Replace the LP gas orifice spud with the correct Natural gas orifice spud.

Refer to the following chart for the correct Natural gas orifice spud placement.

Conversion of Regulator to “LP” on Model 1955

Disconnect Power to Range

Open oven door and remove it, see removal instructions on page 16.

With a Philips driver, undo the 2 screws holding the top down.

Pull top forward about 2" then lift front. Raise the service stay on each side to hold the top up.

On the back right of the range unscrew the nut on top of the regulator.

Reverse the white insert pin by pulling it out of the cap, reverse it, then snap it back into the cap. Replace cap into body of regulator and tighten, making sure not to disturb the regulator spring.

Figure 13

NAT. GAS

LP GAS

Replacing rangetop orifices

Tools required to replace orifices.

Small adjustable wrench.

1.Remove the lift off burner cap.

2.With the small adjustable wrench, unscrew the brass venturi and remove.

3.Unscrew the natural gas orifices in each of the top burners using the 7mm nut driver included with orifice kit. Replace with “LP” orifices listed below.

 

Nat. Gas

LP/Propane

Front left superburner takes

1.75 mm (#50)

.91 mm (#64)

Other front burners take

1.32 mm (#55)

.89 mm (#65)

All rear burners use

1.09 mm (#57)

.71 mm (#70)

Note: example. Orifices are stamped metric sizes. (00) is the number drill equivalent.

4. Reinstall the brass venturi.

Store nat. gas orifices and nut driver so they are available for future conversions.

When replacing the black caps, make sure that the tabs in the cap fit into the grooves of the burner base.

Warning

– Fire Hazard

Locate gas supply shut off valve on the pressure regulator.

Shut off gas supply before converting to L.P. gas.

Make all conversions before turning gas supply valve back on.

Failure to follow these instructions could result in fire, exposion or other personal injury.

A. PLASTIC COVER

B. GAS PRESSURE REGULATOR CAP WITH SOLID END FACING OUT

C. GAS PRESSURE REGULATOR CAP WITH HOLLOW END FACING OUT

D.WASHER

E.GAS PRESSURE REGULATOR CAP

Conversion of Regulator to “LP” on Model 1956 (gas oven)

Remove storage drawer. See page 17.

Locate the regulator at the rear of storage drawer compartment.

Remove the plastic cover from the regulator cap.

With your fingers, turn the nut counter clockwise.

Do not remove the spring beneath the cap.

Turn the cap over so LP faces up and reinstall into regulator.

Replace plastic cover over regulator cap.

OVEN CONVERSION MODEL 1956

To Convert Oven Bake and Broil Burner

1.Remove oven racks.

2.use a 1/2" combination wrench to loosing the orifice hood away from the pin (about 2 to 2-1/2 turns). The oven bake burner flame cannot be properly adjusted if this conversion is not made. See “Adjust Oven Bake Burner Flame” section.

A. ORIFICE HOOD

B.PIN

C.NATURAL GAS: INCREASE GAS – INCREASE FLAME SIZE (PRESET AT FACTORY FOR NATURAL GAS)

D.LP GAS: DECREASE GAS, DEGREASE FLAME SIZE.

To Convert Oven Broiler Burner

1.Use a 1/2" combination wrench to loosen the orifice hood away from the pin (about 2 to 2-1/2 turns. The oven broil burner flame cannot be properly adjusted if this conversion is not made. See “Adjust Oven Broil Burner Flame” section.

2.Reinstall the storage or warming drawer.

3.Complete installation. See “Make Gas Connection” and “Electronic Ignition System” sections.

Checking for proper cooktop burner and oven bake burner flame is very important. Natural gas flames do not have yellow tips.

IMPORTANT: You may have to adjust “LO” setting for each cooktop burner.

12

13

Page 7
Image 7
Elmira Stove Works 1956 Models 1955, Installation of LP Spuds, Conversion of Regulator to LP on Model, Fire Hazard

1955, 1956 specifications

Elmira Stove Works, known for its commitment to quality craftsmanship and vintage aesthetic, made significant strides in the mid-1950s, particularly in the years 1955 and 1956. This era represented not only a peak in the company's production but also a passion for blending nostalgic design with modern technology.

In 1955, Elmira Stove Works offered a range of kitchen appliances that captured the eye with their charming retro styling, reminiscent of the early mid-century modern design. The company emphasized vibrant colors, often presenting stoves and refrigerators in shades of turquoise, pink, and pastel yellow, which added a pop of personality to any kitchen. These colors were more than just for aesthetic appeal; they represented a shift in consumer preferences, where bold hues began to dominate the domestic space.

The stoves produced during this period featured innovative technologies that would appeal to the modern homemaker. They were equipped with advanced ventilation systems to eliminate smoke and odors, making cooking a more pleasant experience. Additionally, the introduction of automatic temperature controls simplified baking and cooking, allowing even novice cooks to achieve consistent results. The use of high-quality enamel finishes not only ensured durability but also made cleanup easier, reflecting the increasing desire for convenience in household appliances.

Another hallmark of Elmira Stove Works in 1956 was the incorporation of more compact and efficient designs, catering to the growing popularity of smaller kitchens. The appliances were designed to maximize functionality without sacrificing style, maintaining an elegant silhouette while providing essential features that supported day-to-day cooking demands.

In this era, Elmira Stove Works also focused on enhancing the consumer experience. Features such as easy-to-read dials and large viewing windows in ovens were designed to assist users in monitoring their cooking while adding an element of elegance to the design. The appeal of these appliances extended beyond their functionality; they were viewed as status symbols, representing modernity and style in the post-war era.

Overall, Elmira Stove Works in 1955 and 1956 showcased a remarkable fusion of mid-century charm and advanced kitchen technology. These appliances not only fulfilled the practical needs of the time but also contributed to the overall aesthetic of the 1950s home, characterized by a passion for style, comfort, and innovation.