8.Reinstall the hanger ball on the downrod (Figure 4) as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod. Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin in captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble.

!WARNING

It is critical that the pin in the hanger ball is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling.

9.The fan comes with blue, black and white leads that are 80-inches long. Before installing the fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

IMPORTANT: When installing the fan blades on the blade flanges, be sure the short side of the fan blade is oriented with the blade flange as shown in Figure 5.

SHORT SIDE OF

FAN BLADE

BLADE FLANGE

Figure 5

10.Use three 10-32 x 8mm Phillips button head screws to secure the fan blade to the upper blade flange (Figure 6). (Refer to IMPORTANT note above.) Repeat the procedure for the remaining four upper blades.

10-32 x 8mm PHILLIPS BUTTON HEAD SCREWS (3)

LABEL LOCATED ON

FAR SIDE

FAN BLADE

UPPER BLADE FLANGE

Figure 6

11.Use three 10-32 x 8mm slotted Phillips button head screws to secure the fan blade to the lower blade flange (Figure 7). (Refer to IMPORTANT note above step 10.) Repeat the procedure for the remaining four lower blades.

10-32 x 8mm PHILLIPS BUTTON HEAD SCREWS (3)

FAN BLADE

LABEL LOCATED ON

FAR SIDE

LOWER BLADE FLANGE

Figure 7

12.Position the lower blade flange on the upper blade flange (Figure 8) and secure the flanges to each other using several strips of masking tape. (The masking tape will be removed later.)

LOWER BLADE FLANGE

MASKING TAPE

Figure 8

UPPER BLADE FLANGE

IMPORTANT: In Steps 13, 14, and 15, DO NOT use electric screwdrivers to install the struts. HAND TIGHTEN ONLY and avoid excessive torque.

13.Slightly separate the upper and lower fan blades and carefully seat the strut into the center holes of the fan blades (Figure 9). Secure the strut by installing two 6-32 x 6mm Phillips button head screws (supplied). Be careful not to scratch the blades.

6-32 X 6mm PHILLIPS BUTTON HEAD SCREWS (2)

FAN BLADE

Figure 9

STRUT

 

5

Page 4 Page 6
Page 5
Image 5
Emerson CF2800BS, CF2800PW, CF2800WB warranty Short Side FAN Blade
Page 4 Page 6

CF2800BS, CF2800WB, CF2800PW specifications

The Emerson CF2800BS, CF2800PW, and CF2800WB ceiling fans are renowned for their combination of style, performance, and advanced technology, making them excellent choices for both residential and commercial spaces. Each model features a sleek contemporary design that seamlessly integrates into a variety of decor styles. With an emphasis on providing exceptional airflow, these fans not only enhance comfort but also contribute to energy savings.

One of the standout features of the CF2800 series is the powerful motor. The high-performance 153mm x 15mm motor delivers efficient airflow, ensuring that even large rooms maintain a comfortable temperature. These fans operate quietly, making them perfect for bedrooms, living rooms, or offices where noise reduction is a priority.

The CF2800BS model boasts a beautiful brushed steel finish, adding an element of modern elegance to any space. It is equipped with five blades, designed for optimized air circulation, and includes an integrated light fixture that enhances illumination in the room.

The CF2800PW model offers a pristine white finish, making it an ideal choice for lighter spaces or traditional aesthetics. This model also features five blades and includes the same high-performing motor found in the other variants, ensuring consistency in performance across the series.

The CF2800WB stands out with its black walnut finish, perfect for creating a warm ambiance in indoor areas. The rich wood tone adds warmth and character while keeping functionality at the forefront. Like its counterparts, it features five meticulously designed blades to maximize airflow efficiency.

Technology integration is a significant highlight of the CF2800 series. Each fan is equipped with a reversible motor, allowing for both summer and winter modes. This feature helps in circulating cool air during hot months and redistributing warm air during colder months, enhancing HVAC efficiency.

Installation is made easy with included mounting hardware, ensuring that homeowners and professionals alike can quickly set up the fans without hassle. The combination of style, advanced airflow technology, energy efficiency, and versatile design makes the Emerson CF2800 series a preferred choice for those seeking both functionality and aesthetic appeal in their ceiling fans.
Top Page Image Contents