How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.
!
WARNING
Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.
1.Disconnect electrical power to the branch circuit at the circuit breaker or fuse box before attempting to install the ceiling fan wall control into the outlet box.
CAUTION: To reduce the risk of electrical shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver.
2.Position the supply wires to the left side of the outlet box (Figure 15); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 15.
NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire.
3.Refer to Figure 15 and 16 and connect the receiver wires to the supply wires and the fan motor wires as follows:
a. Securely connect the green grounding wires from the hanger ball and the hanger bracket to the supply grounding conductor (this may be a bare wire or a wire with green insulation).
b. Securely connect the supply white (neutral) wire to the receiver white (AC IN N) wire.
c.Securely connect the supply black wire (hot) wire to the receiver black (AC IN L) wire.
d.Securely connect the fan motor white wire to the receiver white (TO MOTOR N) wire.
e.Securely connect the fan motor black wire to the receiver black (TO MOTOR L) wire.
f.Securely connect the fan motor blue wire to the receiver blue (FOR LIGHT) wire.
g.If installing the optional accessory AL100 accent light, follow the AL100 installation instructions.
| SUPPLY WHITE WIRE |
|
|
|
|
| |
| (NEUTRAL) | RECEIVER WHITE |
|
|
| ||
|
| WIRE | RECEIVER BLACK | ||||
SUPPLY BLACK | C IN |
| WIRE |
|
|
| |
|
|
|
|
|
| ||
| A |
|
|
|
|
| RECEIVER |
WIRE (HOT) |
|
|
|
|
|
| |
GROUND WIRE |
|
|
|
|
|
| BLACK WIRE |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| RECEIVER |
GREEN GROUND |
|
|
|
|
|
| BLUE WIRE |
|
|
|
|
| MOTOR | L | |
WIRE FROM |
| AC IN L | MOTOR | N |
| FAN | |
|
|
| |||||
HANGER BALL |
|
| LIGHT | TO |
| YELLOW | |
|
|
| TO | FOR |
|
| WIRE |
|
| FAN BLACK |
|
|
|
| |
ANTENNA |
|
|
|
|
|
| |
| WIRE |
|
|
|
|
| |
GREEN GROUND |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
WIRE FROM |
| FAN BLUE WIRE |
|
|
|
|
|
HANGER BRACKET |
|
|
|
|
|
|
|
| FAN WHITE WIRE | |
RECEIVER WHITE | ||
WIRE | ||
STUD (2) | ||
|
Figure 15
| STANDARD |
|
|
| WALL SWITCH | BLACK |
|
|
|
| |
TO 120- | BLACK (HOT) | BLACK |
|
VOLT |
| WHITE |
|
SUPPLY | WHITE |
| |
WHITE |
| ||
|
|
| |
| GROUND | RED |
|
| BLUE | WHITE | |
| CABLE (WITH GROUND) | ||
|
|
| |
| GREEN WIRE (GROUND) | BLACK |
|
| FROM HANGER BALL |
| |
| BLUE |
| |
| AND HANGER BRACKET |
| |
| WHITE |
| |
|
|
| |
| YELLOW | HANGER BALL | |
Figure 16 |
|
| |
!
WARNING
Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.
9 | Model No.: CF990 |
