| Installation & User Manual |
June 2013 | Ed 19UK |
MAS2600 Test sheet
ATT.: | Emerson Process Management |
| Marine Solutions |
| Damcos A/S, Service Department |
FAX.: | +45 5578 7272 |
|
|
Name: |
|
Ship name:
Yard:
NB No:
MAS2600:
Transducer serial no.: |
|
|
|
|
| Amplifier serial no.: |
|
| ||||
Tank name: |
|
|
|
|
|
|
|
|
|
| ||
Liquid in tank |
| HFO: |
| DO: |
|
|
|
| Ballast: |
| Other: | |
The tank is |
| Full: |
|
|
| Empty: |
| Other: |
| |||
Measurements: |
|
|
|
|
|
|
|
|
|
|
| |
1 | Measure voltage between terminal |
|
| V DC | Voltage should be in the range 14 to 33 V DC. | |||||||
| 5 and 6 |
|
|
| Check power supply. |
|
| |||||
|
|
|
|
|
|
|
|
| ||||
2 | Measure ripple voltage between |
|
| V AC | Voltage must not exceed 2 V AC. Check power | |||||||
| terminal 5 and 6 |
|
|
| supply. |
|
| |||||
|
|
|
|
|
|
|
|
| ||||
3 | Measure sensor excitation voltage |
|
|
| V DC | Voltage should be in the range 3.0 to 6.2 V DC | ||||||
| between terminal 7 and 10 |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| |||
4 | Measure sensor excitation voltage |
|
| mV DC | Voltage should be in the range | |||||||
| between terminal 8 and 9 |
|
| |||||||||
|
|
|
|
|
|
|
|
|
| |||
5 | Measure current in supply lead to |
|
|
|
|
| Current should be in the range 4 to 20 mA and the | |||||
| terminal 5 |
|
|
| mA DC | same value as measured in point 6. If not the | ||||||
|
|
|
|
|
|
|
|
| amplifier may be defect. | |||
6 | Measure current in supply lead to |
|
|
|
|
| Current should be in the range 4 to 20 mA and the | |||||
| terminal 6 |
|
|
| mA DC | same value as measured in point 5. If not the | ||||||
|
|
|
|
|
|
|
|
| amplifier may be defect. | |||
7 | Measure sensor resistance with |
|
|
|
|
| If the resistance measured is less that 1 M Ohm the | |||||
| sensor cable unconnected |
|
|
|
|
| sensor is defect. |
|
| |||
| Terminal 7 to cable shield |
|
| M Ohm |
|
|
|
| ||||
| Terminal 8 to cable shield |
|
| M Ohm |
|
|
|
| ||||
| Terminal 9 to cable shield |
|
| M Ohm |
|
|
|
| ||||
| Terminal 10 to cable shield |
|
| M Ohm |
|
|
|
| ||||
8 | Measure sensor bridge resistance |
|
|
|
|
| If the resistance measured is less than 1 K Ohm or | |||||
| with sensor cable unconnected |
|
|
|
|
| greater that 50 K Ohm the sensor is defect. | |||||
| Terminal 7 to Terminal 8 |
|
| K Ohm |
|
|
|
| ||||
| Terminal 7 to Terminal 9 |
|
| K Ohm |
|
|
|
| ||||
| Terminal 7 to Terminal 10 |
|
| K Ohm |
|
|
|
| ||||
| Terminal 8 to Terminal 9 |
|
| K Ohm |
|
|
|
| ||||
| Terminal 8 to Terminal 10 |
|
| K Ohm |
|
|
|
| ||||
| Terminal 9 to Terminal 10 |
|
| K Ohm |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||
9 | Visual inspection of the transmitter: |
|
|
|
|
|
|
|
|
| ||
| Is the cable damaged? |
|
|
|
|
|
|
|
| |||
| Are there sharp bends on the cable? |
|
|
|
|
|
|
|
| |||
| Are there moisture/liquids in the breather tube? |
|
|
|
| |||||||
| Is the diaphragm damaged? |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |
10 | Comments: |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
Page 27 of 28
