5.2.1 Auxiliary Module Controls

Local SIO Configuration Sections

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary module controls

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set-up SIO module

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

- LOCAL SIO CONFIGURATION SECTIONS -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analog output setup...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Serial interface setup...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Configuration of Relay Outputs...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Module installed:

 

 

 

 

 

 

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXPERT

 

 

 

 

 

 

 

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

From the menu "LOCAL SIO CONFIGURATION SECTIONS" you can change to submenus to control and set up several output configurations of the auxiliary SIO module. General Configuration of a SIO board (the whole specification is in another manual):

¨Analog outputs: minimum 2, maximum 8

¨Serial interface (RS 232 or RS 485) to connect the analyzer with a external computer

¨Three relay outputs

If there is a SIO module installed in the platform or in the MLT analyzer, you have to put in "Yes" in the line "Module installed", otherwise "No".

Set up parameters:

¨Select the line of variables or any menu line with the -key or the -key.

¨Select the variable or change to the submenu with the ENTER key or the -key.

¨Select the parameter with the -key or the -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

5 - 30

NGA 2000

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98