Empire Comfort Systems CIBV-30-2 Main Burner Flame Pattern and Figure, Air Shutter Adjustment

Models: CIBV-30-2

1 22
Download 22 pages 58.61 Kb
Page 11
Image 11
Main Burner Flame Pattern (Figure 15 and Figure 16)

If pilot flame pattern is incorrect, as shown in Figure 14

See Troubleshooting, page 16.

Main Burner Flame Pattern (Figure 15 and Figure 16)

Figure 15 shows a correct main burner flame pattern. Figure 16 shows an incorrect main burner flame pattern.

Air Shutter Adjustment

An air shutter adjusting screw is located on the exterior, bottom of the inner body. Screw air shutter adjusting screw IN to close air shutter top (increase yellow flame). Screw air shutter adjusting screw OUT to open air shutter top (decrease yellow flame).

Correct Main Burner Flame

Figure 15

Incorrect Main Burner Flame

Figure 16

If main burner flame pattern is incorrect, as shown in Figure 16

See Troubleshooting, page 16.

Cleaning and Maintenance / Main Burner Warning: Turn off heater and let cool before cleaning

After use, cleaning of the main burner may be required for the proper flame. The main burner may be cleaned by applying air pressure to the ports on the main burner.

Cleaning the Log Set and Firebox

During the annual inspection and maintenance appointment, the service person should clean dust, lint, and any light accumulation from the logs and the firebox area. An extra-soft brush should be used on the logs as they are extremely fragile; a vacuum cleaner may be used on the firebox. If at any time the logs cannot be removed or installed without forcing, the cause must be found. The logs must never be forced.

CAUTION: The ceramic logs are durable when handled and installed properly. However, they are delicate and may be damaged easily if not handled with care. Handling damage to the ceramic logs is not covered by warranty.

DO NOT HANDLE LOGS WHILE THEY ARE HOT. ALLOW PLENTY OF TIME FOR THE APPLIANCE TO COOL COMPLETELY BEFORE HANDLING.

OPERATING INSTRUCTIONS

CIBV-30 ON/OFF/REMOTE Switch

CIBV-30 is equipped with an ON/OFF/REMOTE switch which is located on the wiring chase. A wire harness is attached to the ON/OFF/REMOTE switch. The red, black and green (wires) female push-ons attach to the ON/OFF/REMOTE switch. At the opposite end of the wire harness, the black and green (wires) female push-ons attach to the gas valve. An additional green wire and the red wire, which are stripped and bare, will attach to the 750 millivolt wall thermostat accessory, or, to one of the other accessories that can be purchased for use with your log set.

Operation of ON/OFF/REMOTE Switch with no Accessories

To ignite main burner, turn the control knob on the gas valve from the PILOT position to the ON position. Turn the ON/OFF/REMOTE switch from the OFF position to the ON position. The additional green wire and red wire, which are stripped and bare are not used.

Operation of ON/OFF/REMOTE Switch with Accessories 750 Millivolt Wall Thermostat, GWSG-T

Connect the green and red, stripped and bare, wires on the ON/OFF/ REMOTE switch wire harness to the wall thermostat. Turn the ON/OFF/ REMOTE switch on the wiring chase to the REMOTE position. Set the wall thermostat to the desired temperature.

It is important to use wire of a gauge proper for the length of the wire:

RECOMMENDED WIRE GAUGES

Maximum

Wire

Length

Gauge

1' to 10'

18

10' to 25'

16

25' to 35'

14

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the ON/OFF/ REMOTE switch wire harness to the wall switch. Turn the ON/OFF/ REMOTE switch on the wiring chase to the REMOTE position. Pivot the rocker switch on the FWS-1 to the ON position.

Battery Operated Remote Control, FRBC-1 and FRBTC-1 Connect the green and red, stripped and bare, wires on the ON/OFF/ REMOTE switch wire harness to the remote receiver that is a component in the FRBC-1 and FRBTC-1. Turn the ON/OFF/REMOTE switch on the wiring chase to the REMOTE position. Follow instructions in the FRBC-1 and FRBTC-1 to complete installation.

Note: If batteries fail in FRBC-1 or FRBTC-1, and immediate heat is desired, turn the ON/OFF/REMOTE switch on wiring chase from the REMOTE position to the ON position.

R-3450

Page 11

Page 11
Image 11
Empire Comfort Systems CIBV-30-2 Main Burner Flame Pattern and Figure, Air Shutter Adjustment, Operating Instructions