MAIN BURNER FLAME CHARACTERISTICS

The correct flame will be a short, blue inner flame with a much larger, light blue, outer flame. The burner does not have a primary air adjustment. The flame will be correct if the factory-set pressure and orifice opening are used. After the furnace has been operating, the burner ports may be blocked by foreign matter carried in by combustion air. Therefore, cleaning of the burner may be needed for proper flame.

To clean burner port disconnect the gas supply to the valve, and

 

remove the screws fastening the burner door. After removing the

 

burner door from the burner box, remove each main burner. Pilot

 

mounting bracket will need to be unscrewed and moved out of the

 

way to remove all burners. Burners can be blown out using com-

 

pressed air or by blowing through them. Be sure there is no lint

 

or foreign debris blocking the burner ports. Reassemble using the

 

same screws earlier removed and locate pilot in the same position

 

as before and noted above.

Figure 13

WIRING

The appliance, when installed, must be electrically grounded in ac-

DVC-35T

DVC-35IPT

 

 

cordance with local codes or, in the absence of local codes, with the

 

 

National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

 

 

Code, CSA C22.1, if an external electrical source is utilized. This

 

 

appliance is equipped with a three-prong [grounding] plug for

 

 

your protection against shock hazard and should be plugged

 

 

directly into a properly grounded three-prong receptacle. Do

 

 

not cut or remove the grounding prong from this plug. For an

 

 

ungrounded receptacle, an adapter, which has two prongs and a

 

 

wire for grounding, can be purchased, plugged into the ungrounded

 

 

receptacle and its wire connected to the receptacle mounting screw.

 

 

With this wire completing the ground, the appliance cord plug can

 

 

be plugged into the adapter and be electrically grounded. A 7/8”

 

 

hole is provided in the junction box for use with a conduit connector

 

 

if local codes require this type of protection.

 

 

Thermostat Installation

 

 

The thermostat should be installed in the same room as the furnace

 

 

4’to 5’above the floor and away from another heat source (cooking

 

 

stove, hot water heater, etc.) including walls and doorways with

 

 

a heat source in an adjoining room. Do Not Install Thermostat

 

 

on Outside Wall.

 

 

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

 

Figure 14

13119-6-0107

Page 15

Page 14 Page 16
Page 15
Image 15
Empire Products DVC-35T-1, DVC-35IPT-1 Main Burner Flame Characteristics, Wiring, Thermostat Installation, On Outside Wall
Page 14 Page 16

DVC-35T-1, DVC-35IPT-1 specifications

Empire Products has long been recognized for its commitment to delivering high-quality heating solutions, and two notable offerings are the DVC-35T-1 and DVC-35IPT-1 gas-burning direct vent fireplaces. These units are designed to provide both comfort and aesthetic appeal, making them excellent choices for any home environment.

The DVC-35T-1 model boasts a classic design, paired with modern efficiency. With a heat output of 35,000 BTUs, it effectively warms spaces up to 1,100 square feet, ensuring even heat distribution throughout the room. One of the standout features is its advanced venting system, which allows for horizontal or vertical venting options, making it versatile for different installation layouts. The DVC-35T-1 also comes equipped with an adjustable flame control, enabling users to customize the ambiance to their preference. Its glass viewing area enhances the overall aesthetic while providing a full view of the flames.

On the other hand, the DVC-35IPT-1 model features an innovative design that incorporates a premium fireplace insert. This unit is specifically engineered to fit into existing fireplaces, transforming traditional wood-burning setups into efficient gas-burning heating sources. Like its counterpart, the DVC-35IPT-1 offers a maximum heat output of 35,000 BTUs, providing substantial warmth tailored for spaces up to 1,100 square feet. It is equipped with a state-of-the-art electronic ignition system, which ensures reliable and easy starts every time. The unit also includes a decorative log set that adds to its realism and charm, allowing for a cozy, inviting atmosphere.

Both models prioritize efficiency, with an impressive thermal efficiency rating, which not only helps in reducing heating costs but also makes them environmentally friendly options. The incorporation of a sealed combustion system ensures that indoor air quality is maintained, as it draws outside air for combustion and expels exhaust gases outdoors.

In addition to their technical features, the DVC-35T-1 and DVC-35IPT-1 are designed with user convenience in mind. Remote control capabilities allow for effortless operation, while easy maintenance ensures that homeowners spend less time worrying about upkeep and more time enjoying their fireplaces.

Overall, the Empire Products DVC-35T-1 and DVC-35IPT-1 fireplaces represent a blend of efficiency, technology, and aesthetic appeal, making them ideal options for those looking to enhance their home environment with reliable and stylish heating solutions.
Top Page Image Contents