Installation Instructions

Locating Wall Opening

The furnace is to be located on an outside wall. Locate wall studs so that wall opening will be located between wall studs. The furnace is 14 1/8” in width and can be recessed between standard 16” on center wall studs. The wall opening required as shown in Figure 5 is a diameter of 7 1/2”.

A template is provided in furnace carton for positioning furnace on the wall. Also, refer to Figure 5 and Figure 7 for positioning the furnace on wall and for locating gas line connection.

Installing Optional Side Outlets

Side outlet register, SOR-1may be installed on one or both sides of the furnace at the required clearances of 18” to adjacent wall or combustible material as shown in Figure 6.

1.Turn “OFF” all electric power to the furnace.

2.Remove the front panel from the furnace.

3.Remove the two (2) 8 x 3/8” screws that attach the inner shield cover plate to the inner shield.

4.Scribe a line between the four dimples on the outer casing side to form a square.

5.Drill a pilot hole within the scribed square on the outer casing. Remove the sheet metal within the scribed square with a tin snips or comparable tool. Attention! Do not cut the electrical wires located between the outer casing and the inner shield.

6.Insert the 5” x 5” inner boot through the outer casing. Align the clearance holes on the inner boot with the screw holes on the inner shield. Attach inner boot to inner shield with two (2) 8 x 3/8” screws removed in Step 3.

7.Place the register over the 5 1/2” square opening with the louvers set for the desired direction and mark the mounting holes using the register as a template.

8.Drill two (2) 1/8” diameter holes in cabinet side and attach the register with two (2) 10 x 1” provided screws.

9.Installation of SOR-1 is completed.

Side outlet kit, SOK-1, 10” boot assembly with register, for warm air discharge into an adjoining room may be installed on either side of the furnace at the required clearance of 4” to adjacent wall as shown in Figure 6.

To install SOK-1, please use Steps 1 through 5 in the SOR-1 instructions for DVC-35T furnaces. Now, use the following Steps to complete installation of the SOK-1.

1.Using the inner and outer boots as hole templates, mark and drill four (4) 1/8” (3mm) diameter holes in the inner shield and four (4) 1/8” (3mm) diameter holes in the cabinet side.

2.Locate and cut a 6 3/4” square opening through wall.

3.Attach furnace to wall (see Attaching Furnace to Wall).

4.With furnace in place, after checking alignment of side outlet opening in wall and furnace, place the 9 3/8” x 9 3/8” side outlet wall plate over outer boot, pass the outer boot through the wall and attach side wall plate to furnace side of wall with two (2) 10 x 1 1/2” provided screws.

5.Attach outer boot to the cabinet side with four (4) 8 x 1/4” provided screws.

6.Position and attach inner boot to inner shield with four (4) 8 x 1/4” provided screws.

7.Place the register over the 6 3/4” square opening with the lou- vers positioned for the desired discharge direction and mark the mounting holes using the register as a template.

13119-6-0107

8.Drill two (2) 1/8” diameter holes in the wall and attach the register with two (2) 10 x 1 1/2” provided screws.

9.Installation of SOK-1 is completed.

Figure 5

Figure 6

Page 9

DVC-35T-1, DVC-35IPT-1 specifications

Empire Products has long been recognized for its commitment to delivering high-quality heating solutions, and two notable offerings are the DVC-35T-1 and DVC-35IPT-1 gas-burning direct vent fireplaces. These units are designed to provide both comfort and aesthetic appeal, making them excellent choices for any home environment.

The DVC-35T-1 model boasts a classic design, paired with modern efficiency. With a heat output of 35,000 BTUs, it effectively warms spaces up to 1,100 square feet, ensuring even heat distribution throughout the room. One of the standout features is its advanced venting system, which allows for horizontal or vertical venting options, making it versatile for different installation layouts. The DVC-35T-1 also comes equipped with an adjustable flame control, enabling users to customize the ambiance to their preference. Its glass viewing area enhances the overall aesthetic while providing a full view of the flames.

On the other hand, the DVC-35IPT-1 model features an innovative design that incorporates a premium fireplace insert. This unit is specifically engineered to fit into existing fireplaces, transforming traditional wood-burning setups into efficient gas-burning heating sources. Like its counterpart, the DVC-35IPT-1 offers a maximum heat output of 35,000 BTUs, providing substantial warmth tailored for spaces up to 1,100 square feet. It is equipped with a state-of-the-art electronic ignition system, which ensures reliable and easy starts every time. The unit also includes a decorative log set that adds to its realism and charm, allowing for a cozy, inviting atmosphere.

Both models prioritize efficiency, with an impressive thermal efficiency rating, which not only helps in reducing heating costs but also makes them environmentally friendly options. The incorporation of a sealed combustion system ensures that indoor air quality is maintained, as it draws outside air for combustion and expels exhaust gases outdoors.

In addition to their technical features, the DVC-35T-1 and DVC-35IPT-1 are designed with user convenience in mind. Remote control capabilities allow for effortless operation, while easy maintenance ensures that homeowners spend less time worrying about upkeep and more time enjoying their fireplaces.

Overall, the Empire Products DVC-35T-1 and DVC-35IPT-1 fireplaces represent a blend of efficiency, technology, and aesthetic appeal, making them ideal options for those looking to enhance their home environment with reliable and stylish heating solutions.

Empire Products DVC-35T-1, DVC-35IPT-1 Installation Instructions, Locating Wall Opening

Models: DVC-35T-1 DVC-35IPT-1