Enterasys Networks 5H102-48, 5H103-48 4.3 USING THE RESET BUTTON

Using the RESET Button

Troubleshooting 4-7

4.3 USING THE RESET BUTTON

The RESET button shown in Figure4-2 resets and re-initializes the module.

Figure 4-2 RESET Button (both modules)

To reset the module processor, press and release the RESET button. The module goes through a

reset process for approximately 60seconds. Additional downtime may result as the module

reenters the network.

CAUTION: Pressing the RESET button resets the device, and all current switching

being performed by the module is halted. A network downtime of up to two minutes will

result from this action for any devices connected to the module.

NOTE: Pressing the RESET button while the module is already in reset mode is not

recommended. If the RESET button is pressed while the module is in reset mode, the

module will enter an extended diagnostic procedure, which is unnecessary for norm al

operation. This extended diagnostic procedure takes longer than one minute to

complete.

FAST ENET

5H102-48

GROUP

GROUP

SELECT

RESET

COM

CPU

1X

G

R

O

U

P

GROUP

RESET Button

Contents

Main 5H102-48 and 5H103-48 Fast Ethernet Installation Guide FAST ENET 5H103-48 FAST ENET 5H102-48 Page i NOTICE ELECTRICAL HAZARD: Only qualified personnel should perform installation procedures. ii FCC NOTICE INDUSTRY CANADA NOTICE VCCI NOTICE iii ENTERASYS NETWORKS, INC. PROGRAM LICENSE AGREEMENT iv v DECLARATION OF CONFORMITY Page vii Contents ABOUT THIS GUIDE 1 2 3 4 A B ix Figures Page About This Guide USING THIS GUIDE STRUCTURE OF THIS GUIDE Important Notice RELATED DOCUMENTS DOCUMENT CONVENTIONS The guide uses the following conventions: GETTING HELP Introduction Important Notice 1-2 Introduction Figure 1-1 The 5H102-48 and 5H103-48 Modules 1.1 CONNECTIVITY 1.2 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.3 PORT TRUNKING 1.4 REMOTE MONITORING (RMON) 1.5 PORT/VLAN REDIRECT FUNCTION 1.6 FLOW CONTROL 1.7 802.1 PORT PRIORITY 1.8 MANAGEMENT 1.9 SWITCHING OPTIONS 1.10 STANDARDS COMPATIBILITY 1.11 LANVIEW DIAGNOSTIC LEDs Page Network Requirements 2.1 PORT TRUNKING FEATURE 2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK Installation 3.1 UNPACKING THE MODULE Page 3.2 INSTALLING THE MODULE INTO THE 5C105 CHASSIS Installing the Module into the 5C105 Chassis 3-4 Installation Figure 3-1 Installing a Module into the 5C105 Chassis 35861_02 45 3.3 CONNECTING TO THE NETWORK 3.3.1 Connecting UTP Cables to the 5H102-48 Page Connecting to the Network Installation 3-7 Figure 3-3 Crossover Cable RJ45 Pinouts Figure 3-4 Straight-Through Cable RJ45 Pinouts 3.3.2 Connecting UTP Cables to the 5H103-48 Page 3.4 COMPLETING THE INSTALLATION Troubleshooting 4.1 USING LANVIEW Using LANVIEW 4-2 Troubleshooting Figure 4-1 LANVIEW LEDs (both modules) Tabl e 4-1 describes the LED indications and provides recommended actions as appropriate. FAST ENET 5H102-48 GROUP SELECT Port 1, Group 1 LEDs Page Page 4.2 TROUBLESHOOTING CHECKLIST Page Using the RESET Button Troubleshooting 4-7 4.3 USING THE RESET BUTTON RESET Button The RESET button shown in Figure4-2 resets and re-initializes the module. Page A Specifications A.3 ENVIRONMENTAL REQUIREMENTS A.1 MODULE SPECIFICATIONS A.2 PHYSICAL PROPERTIES A.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTS A.6 REGULATORY COMPLIANCE Page B Mode Switch Bank Settings and Options B.1 REQUIRED TOOLS B.2 SETTING THE MODE SWITCHES Page Page Index Index-2 P R S T U