Enterasys Networks 5H102-48, 5H103-48 P, R, S, T, U, V

Index-2

Physical properties A-1

Pinouts

crossover 3-7

straight-through 3-7

Port redirect function

introduction to 1-4

Port Trunking

introduction to 1-3

Receive LEDs

viewing of 4-1

Redirect functions

port and VLAN

introduction to 1-4

Regulatory Compliance A-3

Related manuals xii

Remote Monitoring (RMON)

introduction to 1-3

RESET button 4-7

Specifications A-1

Standards compatibility 1-5

Switching options

introduction to 1-5

Transmit LEDs

viewing of 4-1

Troubleshooting 4-1

checklist 4-5

Unpacking the module 3-2

Viewing Receive and Transmit Activity

instructions for 4-1

VLAN redirect function

introduction to 1-4

Contents

Main 5H102-48 and 5H103-48 Fast Ethernet Installation Guide FAST ENET 5H103-48 FAST ENET 5H102-48 Page i NOTICE ELECTRICAL HAZARD: Only qualified personnel should perform installation procedures. ii FCC NOTICE INDUSTRY CANADA NOTICE VCCI NOTICE iii ENTERASYS NETWORKS, INC. PROGRAM LICENSE AGREEMENT iv v DECLARATION OF CONFORMITY Page vii Contents ABOUT THIS GUIDE 1 2 3 4 A B ix Figures Page About This Guide USING THIS GUIDE STRUCTURE OF THIS GUIDE Important Notice RELATED DOCUMENTS DOCUMENT CONVENTIONS The guide uses the following conventions: GETTING HELP Introduction Important Notice 1-2 Introduction Figure 1-1 The 5H102-48 and 5H103-48 Modules 1.1 CONNECTIVITY 1.2 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.3 PORT TRUNKING 1.4 REMOTE MONITORING (RMON) 1.5 PORT/VLAN REDIRECT FUNCTION 1.6 FLOW CONTROL 1.7 802.1 PORT PRIORITY 1.8 MANAGEMENT 1.9 SWITCHING OPTIONS 1.10 STANDARDS COMPATIBILITY 1.11 LANVIEW DIAGNOSTIC LEDs Page Network Requirements 2.1 PORT TRUNKING FEATURE 2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK Installation 3.1 UNPACKING THE MODULE Page 3.2 INSTALLING THE MODULE INTO THE 5C105 CHASSIS Installing the Module into the 5C105 Chassis 3-4 Installation Figure 3-1 Installing a Module into the 5C105 Chassis 35861_02 45 3.3 CONNECTING TO THE NETWORK 3.3.1 Connecting UTP Cables to the 5H102-48 Page Connecting to the Network Installation 3-7 Figure 3-3 Crossover Cable RJ45 Pinouts Figure 3-4 Straight-Through Cable RJ45 Pinouts 3.3.2 Connecting UTP Cables to the 5H103-48 Page 3.4 COMPLETING THE INSTALLATION Troubleshooting 4.1 USING LANVIEW Using LANVIEW 4-2 Troubleshooting Figure 4-1 LANVIEW LEDs (both modules) Tabl e 4-1 describes the LED indications and provides recommended actions as appropriate. FAST ENET 5H102-48 GROUP SELECT Port 1, Group 1 LEDs Page Page 4.2 TROUBLESHOOTING CHECKLIST Page Using the RESET Button Troubleshooting 4-7 4.3 USING THE RESET BUTTON RESET Button The RESET button shown in Figure4-2 resets and re-initializes the module. Page A Specifications A.3 ENVIRONMENTAL REQUIREMENTS A.1 MODULE SPECIFICATIONS A.2 PHYSICAL PROPERTIES A.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTS A.6 REGULATORY COMPLIANCE Page B Mode Switch Bank Settings and Options B.1 REQUIRED TOOLS B.2 SETTING THE MODE SWITCHES Page Page Index Index-2 P R S T U