Initial Installation

QUALIFIED INSTALLERS ONLY

HORIZONTAL INSTALLATION:

1.Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of

the appliance.

2.Direct vent pipe and fittings are designed with special twist-lock connections. Assemble the desired combination of black pipe and elbows to the appliance adapter with pipe seams oriented towards the wall or floor, as much out of view as possible.

Place a bead of Mil-Pac on the outer edge of the inner exhaust pipe (non-flared end). Place a bead of high temperature silicone on the male edge of the outer pipe. Push the pipe sections completely together, then twist-lock one section clockwise approximately 1⁄4 turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside, on black pipe. They may be located by examining the inside of the female ends as shown in Figure 25.

Female

Locking

Lugs

Sealant

Male

Locking

Lugs

Figure 25: Twist-Lock Connection

Notes:

 

 

 

 

 

 

 

(a) Twist-lock procedure: four (4) indentations, located on the female

10"

end of the pipes and fittings, are designed to slide straight onto the

(254mm)

male ends of adjacent pipes and fittings, by orienting the four pipe

 

indentations so they match and slide into the four entry slots on the

10"

male end.

 

 

 

 

 

 

 

 

 

 

 

 

(254mm)

(b) Horizontal runs of vent pipe must be supported every 36” (915mm).

 

Wall straps are available for this purpose, also when running horizontal

 

pipe

minimum

clearances

to

combustibles

must

be

maintained;

 

2” (51mm) at top, 11⁄2” (38mm) at sides, 11⁄2” (38mm) at

 

bottom.

 

 

 

 

 

 

 

3. With the pipe attached to the stove in the correct location, mark the

 

wall for a 10” (25.4cm) x 10” (25.4 cm) square hole (refer to Figure

 

26). The center of the square hole should match the center line of

Figure 26: Wall Framing Hole for

the horizontal pipe. Cut and frame the 10” (25.4cm) x 10” (25.4cm)

hole in the exterior wall where the vent will be terminated. Refer to

Horizontal Installation.

 

Figure 18. If the wall being

11/4"

 

 

 

 

penetrated is constructed of

 

 

 

 

non-combustible material i.e.

(3.2cm)

 

 

 

 

 

 

 

 

 

masonry or concrete, a 7”

Fold strap

 

 

 

Woodscrews

(17.8cm) hole is acceptable.

here

 

 

 

 

4. Position the horizontal vent

 

termination

in

the

center

Sheet metal

of

the

10”

(25.4cm)

x

10”

screws

(25.4cm)

hole,

and

attach

 

to

the

 

exterior

 

wall

with

 

the

four

screws

provided.

Wall Thimble

Before

attaching

the

 

vent

 

Strap

termination

to the exterior

Figure 27: Installing Decorative Wall Thimble.

 

 

 

 

 

 

 

 

 

20

Page 19 Page 21
Page 20
Image 20
Enviro 50-1033 owner manual 51mm at top, 11⁄2 38mm at sides, 11⁄2 38mm at Bottom, Twist-Lock Connection
Page 19 Page 21

50-1033 specifications

The Enviro 50-1033 is an innovative, environmentally-friendly vehicle designed to meet the growing demand for sustainable transportation solutions. As a part of the advanced Enviro series, the 50-1033 stands out due to its blend of efficiency, performance, and eco-conscious features.

One of the defining characteristics of the Enviro 50-1033 is its low-emission engine technology. The vehicle is equipped with a state-of-the-art diesel engine that adheres to stringent emission standards, significantly reducing pollutants compared to traditional models. This feature not only lessens the environmental footprint but also contributes to improved air quality in urban settings.

Additionally, the Enviro 50-1033 incorporates advanced fuel efficiency technologies, making it an economical choice for fleet operators. With a focus on maximizing fuel economy without compromising performance, this vehicle is designed to deliver cost savings over its lifecycle. The engine employs a combination of turbocharging and high-pressure fuel injection systems, which enhances combustion efficiency and maximizes power output while minimizing fuel consumption.

The vehicle’s design is another noteworthy aspect. Built with lightweight materials and aerodynamics that reduce drag, the Enviro 50-1033 enhances overall performance and maneuverability. The spacious interior is designed to accommodate a larger number of passengers without sacrificing comfort. Ergonomically designed seating and high-quality materials create an inviting atmosphere for both drivers and passengers.

Safety features are a top priority in the Enviro 50-1033. The vehicle is equipped with advanced driver assistance systems, including anti-lock braking systems, traction control, and electronic stability control. These technologies work together to enhance vehicle safety, providing peace of mind for operators and passengers alike.

The Enviro 50-1033 also offers modular design options, allowing customization to meet the specific needs of various transportation services. Whether for public transport, private hire, or shuttle services, the flexibility of the Enviro 50-1033 ensures that it can adapt to diverse operational demands.

In conclusion, the Enviro 50-1033 is a remarkable vehicle that embodies the future of sustainable transportation. With its cutting-edge technologies, eco-friendly features, and commitment to safety and comfort, it represents a significant step forward in the quest for greener urban mobility solutions. As cities globally embrace the transition to cleaner transportation options, the Enviro 50-1033 is well-positioned to play a vital role in shaping the future of public transport.
Top Page Image Contents