Manuals / Epson / Computer Equipment / Switch

Epson MLC 104 IP Plus Hardware Setup, cont’d Left Side/Top Panel Features and Connections

Models: MLC 104 IP Plus

1 26

Download 26 pages 17.88 Kb

Page 12

Hardware Setup, cont’d

Hardware Setup, cont’d

Left Side/Top Panel Features and Connections

IR

MLC 104 IP Plus

Top Panel

2"–12" (4–30 cm)

RESET

MLC 104 IP Plus Left Side

1

IR

MLC 104 IP Plus

Top Panel

2

The IR learning range for the MLC 104 IP Plus

NBecause the top panel of the MLC 104 IP Plus is obscured after wall mounting, perform all IR learning prior to installation.

A	Reset button and LED — Pressing this recessed button causes
	various IP functions and Ethernet connection settings to be reset
	to their factory defaults. For reset modes, refer to chapter 2 in
	the MLC 104 IP Plus User's Manual.
B	IR signal sensor — This sensor allows for IR learning. It
	receives and "learns" commands from other devices' infrared
	remote controls so an IR driver can be created. Refer to the
	IR Learner Help File from the IR Learner software for IR learning
	procedures. This receiver accepts infrared signals from 30 kHz
	to 62 kHz.
	N You can download the IR Learner software from the Extron
	Web site (www.extron.com).

2-8

MLC 104 IP Plus • Hardware Setup

MLC 104 IP Plus • Hardware Setup

2-9

Image 12

Epson setup guide Hardware Setup, cont’d Left Side/Top Panel Features and Connections, MLC 104 IP Plus Hardware Setup

Contents

Setup Guide MLC 104 IP PlusMediaLinkTM Controller 68-1289-01 Rev. APrecautions Extron’s WarrantySafety Instructions English FCC Class A Notice安全须知中文这个符号提示用户该设备用户手册中有重要的操作和维护说明。这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。Table of Contents Chapter Two MLC 104 IP Plus Hardware SetupChapter Three MLC 104 IP Plus Software Setup Step 7 Configure the Control Modules Using theTable of Contents, cont’d Step 11 Build and Upload a ConfigurationAbout Global Configurator System Requirements Installing the Software Chapter1OneAbout Global Configurator IntroductionAbout this Manual About the MLC 104 IP Plus Medialink ControllersInstalling the Software Introduction, cont’dSystem Requirements Updating FirmwareMLC 104 IP Plus Hardware Setup Right Side Panel Features and ConnectionsLeft Side/Top Panel Features and Connections Front Panel Features and Basic OperationHardware Setup Right Side Panel Features and ConnectionsThe SCPs DIP switch #4 set to ON up for an MLC 104 IP Plus connection MLC 104 IP Plus Hardware SetupHardware Setup, cont’d MLC 104 IP Plus Hardware SetupAn MLC 104 IP Plus controller daisy chained to a SCP 104 remote panel An equivalent digital I/O port circuitHardware Setup, cont’d Power wiringPWR power connector - To provide power to the MLC LAN port defaults are as followsHardware Setup, cont’d Left Side/Top Panel Features and Connections MLC 104 IP Plus Hardware SetupThe IR learning range for the MLC 104 IP Plus Hardware Setup, cont’d Front Panel Features and Basic Operation Volume controlConfiguration host control port ButtonsMLC 104 IP Plus Software Setup Hardware Setup MLC 104 IP PlusChapter3Three Software Setup Step 1 Download Device Drivers2. Click the Add Drivers Subscription button Software Setup, cont’d Step 2 Create a New Project Step 3 Add an MLC 104 IP Plus Controller and Define its LocationProject Settings dialog box Add Device from the Edit menuSoftware Setup, cont’d Defining e-mail server settingsStep 4 Define E-mail Settings The Global Configurator Front Panel windowSetting up e-mail notifications Adding e-mail contactsSoftware Setup, cont’d the Contact Manager dialog boxSoftware Setup, cont’d Step 5 Add a Serial and an IR Device Downloading additional driversAdding a serial driver Add serial driver windowStep 6 Configure the Front Panel Buttons Adding an IR driverSoftware Setup, cont’d Front Panel window with configured buttonsConfiguring an input button Configuring the On and Off buttonsStep 7 Configure the Control Modules Using the Auto Fill Feature Software Setup, cont’dSoftware Setup, cont’d Control module configurationControl module main window Input 2 button selectionSoftware Setup, cont’d Step 8 Create a Display Shutdown Schedule choose the Epson PowerLite 7700p from the Subject PortActions window. The Scheduled Actions Wizard dialog Enter a name Shutdown in the Enter Scheduled ActionStep 9 Create a Display Lamp Hour Warning E-mail Software Setup, cont’dConditions dialog. The Monitored Conditions Wizard Enter a name Lamp hour in the Enter MonitoredSoftware Setup, cont’d Step 10 Create a Display Disconnection E-mail Step 11 Build and Upload a ConfigurationBuilding a configuration Uploading a configurationAccessing GlobalViewer Software Setup, cont’d3-24 MLC 104 IP Plus Software Setup Test GV System button