OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Cleaning the Pre-Motor Filter
1.Pull the
Upholstery Brush
The upholstery brush is conveniently mounted on the back of the main body of the vacuum cleaner. The brush can be used for cleaning the furniture, Venetian blinds, books, lamp shades and shelves. (Fig. 14)
The efficiency of your turbo brush depends on the bristle brush rotating at high speed. Strong air suction is needed to accomplish this. In order to ensure that maximum air suction is maintained, please read the following instructions:
1. | Empty the dust cup frequently |
| during use. |
2. | Inspect the rotating bristle brush |
| and air turbine wheel regularly. |
Using the Vacuum for Above Floor Cleaning
1. | Place the vacuum cleaner in the |
| upright position. |
2. | Set the carpet height adjustment |
| knob to the highest setting “ ”. |
3. | To attach the accessories to the |
| flexible hose, remove the hose from |
| the hose connector and push the |
Fig. 11
2.Remove the
Fig. 14
Extension Tube
This attachment is stored on the right side of the cleaner on it’s own holder in front of where the flexible hose ttaches to the hose connector. This tool is designed to extend your reach. Attach this accessory by it’s narrower end to the flexible hose and use for hard to reach places. (Fig. 15)
Inspect the turbine wheel and air |
passage for debris and/or blockages. |
Remove debris if present. |
3. Inspect the rotating brush for a build |
up hair or string. If present, remove |
by carefully cutting with scissors. |
Avoid damaging or cutting the |
bristles. |
Cleaning the Pet Hair Turbo Brush
To clean the pet hair turbo brush:
desired accessory onto the end. |
4. If additional length is required, the |
handle may be used. Remove the |
handle from the main body by first |
lifting the handle locking lever. Push |
the end of the flexible hose into the |
opening at the back of the handle. |
Attach the desired accessory to the |
end of the handle. |
5. The crevice tool, turbo brush and |
upholstery brush can also be |
attached to the end of the extension |
Fig. 12
3.Allow both parts to air dry completely before placing the filter back in the frame and sliding the frame back into the main body. Let the
Using the Accessories IMPORTANT: Make sure the vacuum cleaner is turned off when attaching or removing any accessories. CAUTION: DO NOT pull the vacuum cleaner around by the hose. DO NOT over stretch the hose. Trying to reach beyond the hose’s extent may cause the vacuum cleaner to tip over.
Crevice Tool
The crevice tool is located inside the extension tube and can be used for radiators, crevices, corners, baseboards and between cushions. (Fig. 13)
Fig. 15
Turbo Brush
The turbo brush conveniently attaches to the handle with an attaching bracket.
1. Ensure that the handle is attached |
to the main body before attaching |
the turbo brush to the handle. |
2. First attach the turbo brush to the |
attaching bracket by hooking the |
edge of the opening under the |
trapdoor on the bottom of the turbo |
brush to the flat part of the bracket. |
Then press the tube part of the |
turbo brush against the clip on the |
bracket until the two pieces snap |
together. |
3. Hold the assembled pieces by the |
turbo brush and touch the two clips |
on the bracket to |
the metal tube of |
the handle. Hold |
the handle from |
the top and |
squeeze the two |
pieces together, |
putting more |
force on the |
bigger clip until |
the bracket |
snaps on. |
1.Hold the turbo brush in your hand and with the help of a screwdriver, gently pry the cover off. (Fig. 17)
Fig. 17
2.Inspect turbine wheel and air passage for debris and/or blockage. Remove any debris if present.
3.Inspect the rotating brush for
4.Once clean, align the cover of the turbo brush with the edge of the brush and snap it closed. (Fig. 18)
tube. | |
6. Ensure that the attachment you are | |
using is appropriate for the surface | |
you are cleaning. | |
7. To return to vacuuming the floor, | |
perform the following steps: | |
• | Detach the hose from the handle |
| and push it snugly back into the |
| hose connector. |
• | Hang the flexible hose back onto |
| the hose holder. |
• | Return the handle to it’s regular |
| position in the opening on top of |
| the main body and push down the |
| handle locking lever to lock the |
| handle into place. |
• | Return the carpet height |
| adjustment knob to the appropriate |
| setting. |
Fig. 13
4. Remove the turbo |
brush from the bracket in order to use. (Fig. 16)
7
Fig. 18
8