BDS
Verify Line Voltage Before Using, Unpacking, Installation Location, Cleaning, Moving the Receiver and Introduction
Introduction
Please register your product on our Web site at www.harmankardon.com.
Note: You’ll need the product’s serial number. At the same time, you can choose to be notified about our new products and/or special promotions.
Thank You for Choosing Harman Kardon® Products!
In the years since harman kardon engineers invented the
To get the maximum enjoyment from your new BDS system, we urge you to read this manual thoroughly and refer back to it as you become more familiar with your new system’s features and their operation.
If you have any questions about this product, its installation or its operation, please contact your retailer or custom installer, or visit the Harman Kardon Web site at www.harmankardon.com.
Verify Line Voltage Before Using
Your BDS receiver has been designed for use with 110 –
Connection to a line voltage other than that for which the units are intended can create a safety and fire hazard and may damage the units. If you have any questions about the voltage requirements for your specific model or about the line voltage in your area, contact your dealer before plugging the unit into a wall outlet.
Unpacking
The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move or if the unit ever needs repair.
To minimize the size of the carton in storage, you may wish to flatten it. You can do it by carefully slitting the tape seams on the carton’s bottom and collapsing it. You can store cardboard inserts in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.
If you do not wish to save the packaging materials, please note that the carton and other sections of the
Remove the protective plastic film from the
Installation Location
tTo ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.
tProvide proper space both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the area. Under some circumstances, a fan may be required.
tDo not place the unit directly on a carpeted surface.
tAvoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.
tAvoid moist or humid locations.
tDo not obstruct the ventilation slots on the top and sides of the unit or place objects directly over or next to them.
tDo not place the receiver directly on top of a product that generates excessive heat.
tDue to the heat generated by the receiver and other components in your system, there is the remote possibility that the rubber padding on the bottom of the unit’s feet may leave marks on certain wood or
tYour new harman kardon
Cleaning
receiver
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.
Speakers and Subwoofer
When needed, use a soft cloth to remove any fingerprints or dust from the enclosures or grilles. NOTE: Do not use any cleaning products or polishes on the enclosures or grilles.
Moving the Receiver
Before moving the receiver, disconnect any interconnection cords to other components, and disconnect the unit from its AC outlet.
NOTE: The
tBDS receivers sold in the USA are designed only for playback of discs with Blu- Ray Disc Region Code A and DVD Region Code 1 information, or for discs that do not contain any region code information.
tBDS receivers sold in Europe are designed only for playback of discs with
If there is a Region Code on a disc other than the one your BDS player is designed for, it will not play in your BDS receiver.
ENGLISH
3