Viewing the current configuration |
|
|
|
|
|
|
|
| ||||
The current configuration can be viewed using the front panel buttons. Press and | ||||||||||||
release the Output button and the LED for the input tied to it will light. If, when | ||||||||||||
you view video and audio ties, the Audio LED blinks and the Video LED is on after | ||||||||||||
selecting an input or output, the LEDs indicate that the audio ties are not the same | ||||||||||||
as the video ties for that input (audio breakaway is |
|
|
|
|
|
| ||||||
active). |
|
|
|
|
|
|
|
| = LED Off |
| ||
Viewing and adjusting the audio level |
|
| 1 = Slow blink = 1dB | |||||||||
|
| 2 = Fast blink = 2dB |
| |||||||||
The audio level of each input can be displayed and |
|
|
| = LED On = 3dB |
| |||||||
|
| Input LED |
|
| ||||||||
adjusted through a range of |
|
|
|
| ||||||||
dB | 1 | 2 | 3 | 4 | ||||||||
that there is no noticeable volume difference among | +24 |
|
|
|
|
| ||||||
sources. The audio level can be adjusted from the front |
|
|
|
|
| |||||||
+23 |
| 2 |
|
|
| |||||||
panel or by using Extron’s |
|
|
|
| ||||||||
+22 |
| 1 |
|
|
| |||||||
program. To adjust the audio level of an input from |
|
|
|
| ||||||||
+21 |
|
|
|
|
| |||||||
the front panel: |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| +20 | 2 |
|
|
|
| ||
1. | Select an input, then press and hold the Conf/ |
|
|
|
| |||||||
+19 | 1 |
|
|
|
| |||||||
| Save button until the I/O LED begins to blink | +18 |
|
|
|
|
| |||||
| (approx. 5 seconds), indicating that the audio | +17 |
|
|
| 2 |
| |||||
| adjustment mode is active. The Input LEDs, and | +16 |
|
|
| 1 |
| |||||
| the decrement ( | ) and increment ( | ) LEDs, | +15 |
|
|
|
|
| |||
| display the audio level. The Video/+dB displays | +14 |
|
|
| 2 |
| |||||
| positive (+) polarity and the | +13 |
|
|
| 1 |
| |||||
| negative polarity. Both LEDs are lit to indicate | +12 |
|
|
|
|
| |||||
| 0dB. |
|
|
|
|
| +11 |
|
|
| 2 |
|
2. | Press and release an input button to select an input. | +10 |
|
|
| 1 |
| |||||
+9 |
|
|
|
|
| |||||||
3. | Each Input LED, and the Decrement ( | ) and |
|
|
|
|
| |||||
+8 |
|
| 2 |
|
| |||||||
| Increment ( | ) LEDs, indicate 0dB when off, 1dB |
|
|
|
| ||||||
| +7 |
|
| 1 |
|
| ||||||
| when blinking slowly, 2dB when blinking quickly, |
|
|
|
| |||||||
| +6 |
|
|
|
|
| ||||||
| and 3dB when lit. Refer to the chart at right. |
|
|
|
|
| ||||||
| +5 |
| 2 |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||
4. | Press and release the Decrement or Increment | +4 |
| 1 |
|
|
| |||||
| button to increase or decrease the audio input | +3 |
|
|
|
|
| |||||
| level. |
|
|
|
|
| +2 | 2 |
|
|
|
|
5. | Press and hold the Conf/Save button until the | +1 | 1 |
|
|
|
| |||||
|
|
|
|
|
| |||||||
| I/0 LED turns off to save the attenuation or gain | 0 |
|
|
|
|
| |||||
|
|
|
|
|
|
| ||||||
| value in memory and exit the audio display and | 1 |
|
|
|
| ||||||
|
|
|
|
|
|
| ||||||
| adjustment mode. |
|
| 2 |
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||||
| 1. | There is one audio level setting per input. |
|
|
|
|
| |||||
|
| 1 |
|
|
| |||||||
|
| The audio level setting is shared by the left |
|
|
|
| ||||||
|
|
| 2 |
|
|
| ||||||
|
| and right audio inputs. |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |
| 2. | The audio level settings are stored in non- |
|
| 1 |
|
| |||||
|
| volatile memory. When power is removed |
|
| 2 |
|
| |||||
|
| and restored, the audio level settings are |
|
|
|
|
| |||||
|
| retained. |
|
|
|
|
| 1 |
| |||
Example 3: Viewing and adjusting an audio level |
|
|
| 2 |
| |||||||
|
|
|
|
| ||||||||
See figure |
|
|
| 1 |
| |||||||
of viewing and adjusting the audio level. |
|
|
|
|
| 2 |
| |||||
A Press and hold the Conf/Save button until the |
|
|
|
|
| |||||||
|
|
| 1 |
| ||||||||
| I/O LED begins to blink, indicating that the |
|
|
|
| |||||||
|
|
|
| 2 |
| |||||||
| audio adjustment mode is active. |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
CrossPoint 42 HVA Matrix Switcher • Operation |