Extron electronic N 60-796-01 setup guide Remote Control, cont’d, Create ties, Set input format

	4-4
Refer also to	MPX Plus 866
the MPX Plus 866 A User’s	A • RemoteControl

Command	ASCII command	Response	Additional description
	(host to switcher)	(switcher to host)

Create ties

N• Video ties cannot be made between the computer video group and the low resolution video group.

•Program audio ties can only be made to the computer/audio output group (outputs 1 through 6).

•Mixing audio inputs into the output audio using SIS commands requires a complex command. Refer to the MPX Plus 866 A User's Manual.

•Video and audio ties between the low resolution video input group and the low resolution video outputs group are always made with the program audio redirected. In such an operation, the switcher automatically ties the audio to an output in the computer/audio outputs group (outputs 1 through 6) as follows:

 If the video is tied to output 7, the audio is tied to output 1.		 If the video is tied to output 10, the audio is tied to output 4.
	If the video is tied to output 8, the audio is tied to output 2.		If the video is tied to output 11, the audio is tied to output 5.
	If the video is tied to output 9, the audio is tied to output 3.		If the video is tied to output 12, the audio is tied to output 6.

•Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*2&02*04%4*6$.

•The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).

NThe & tie command for RGB and the % tie command for video can be used interchangeably, but you cannot switch between groups.

NThe & read tie command for RGB and the % read tie command for video can be used interchangeably.

Remote Control, cont’d

Manual at www.extron.com.

Tie input X! to output X@, video	X!*X@!
and audio
Example:	1*3!
	11*9!

OutX@•InX!•All] (within computer video group)

— or —

Qik] (within low resolution video group [because of audio redirect])

	Tie input X!‘s video and audio to output
	X@.
Out03•In01•All]	Tie input 1 video and audio to output 3.
Qik]	Tie input 11 video to output 9
	and input 11 audio to output 5.

N X! = Input number	00 – 08 (computer video input group) or 00, 09 – 14 (low resolution video input group) (00 = untied)
X@ = Output number	01 – 06 (Computer video and audio output group) or 07 – 12 (low resolution video output group)

Refer also to the MPX Plus 866 A User’s	MPX Plus
Manual at	866 A
www.extron.com.	• Remote Control

Command	ASCII command	Response	Additional description
	(host to switcher)	(switcher to host)
Create ties (continued)
Tie input X! to output X@,	X!*X@&	OutX@•InX!•RGB]	Audio breakaway.
computer only
Example:	5*4&	Out04•In05•RGB]	Tie input 5 RGB to output 4.
(see 2nd Note, above)
Tie input X! to output X@, video	X!*X@%	OutX@•InX!•Vid]	Audio breakaway switching.
only
Example:	9*7%	Out07•In09•Vid]	Tie input 9 video to output 7.
(see 2nd Note, above)
Tie input X! to output X@, audio	X!*X@$	OutX@•InX!•Aud]	Audio breakaway switching.
only
Example:	12*4$	Out04•In12•Aud]	Tie input 12 audio to output 4.
Read computer video output tie	X@&	X!]	RGBHV input X! is tied to output X@.
Read video output tie	X@%	X!]	Video input X! is tied to output X@.
Read audio output tie	X@$	X!]	Audio input X! is tied to output X@.
Set input format
Set input video format	X!*X#\	TypX!*X#]	Set the video format to X# for input X!.

NThe only valid input (X!) numbers are 11 through 14.

Example:	11*1\	Typ11*1]	Set input 11 to composite video.
Read input format	X!\	X#]	Show the video format of input X!.
N X! = Input number	00 – 08 (computer video input group) or 00, 09 – 14 (low resolution video input group) (00 = untied)
X@ = Output number	01 – 06 (Computer video and audio output group) or 07 – 12 (low resolution video output group)
X# = video format	1 = composite video	2 = S-video

4-5