Installation and Operartion, cont’d
Switch modes
The SW6 VGA Audio switcher operates in manual or auto switch mode.
•Manual switch mode — Input selection is done using Input buttons 1 through 6 on the front panel or through the rear panel Remote connector (contact closure or
•Auto switch mode — The switcher automatically selects the highest number input that has sync pulses available. Input selection by the front panel switches or through the Remote connector is blocked.
Determining the switch mode
To determine which mode is active, press and release an unselected input button.
Normal switch mode — That input becomes the selected input.
Auto switch mode — The switcher does not select the input associated with the button that you pushed.
Selecting a switch mode
Switch between modes by pressing and holding the Mode (Input 1 button) and either the Normal (Input 2) or Auto (Input 3) button until either the Normal or Auto LED blinks (figure
Press and HOLD.
1 sec.
The blinking LED indicates the mode.
Release the buttons.
Figure 2-10 — Selecting a switch mode
Audio level control |
|
|
|
| Input LED |
|
| |||
dB | 1 | 2 | 3 | 4 | 5 | 6 | +dB | |||
The audio level setting for the | ||||||||||
+9 |
|
|
|
|
|
|
| |||
selected input can be viewed | +8 |
|
| F |
|
|
|
| ||
and changed (within a range of |
|
|
|
|
|
| ||||
+7 |
|
| S |
|
|
|
| |||
|
|
|
|
|
| |||||
+6 |
|
|
|
|
|
|
| |||
there is no noticeable volume |
|
|
|
|
|
|
| |||
difference among sources. | +5 |
| F |
|
|
|
|
| ||
Adjusting the audio level | +4 |
| S |
|
|
|
|
| ||
+3 |
|
|
|
|
|
|
| |||
View or change the audio input |
|
|
|
|
|
|
| |||
+2 | F |
|
|
|
|
|
| |||
level as follows: |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||
1. | Select an input. | +1 | S |
|
|
|
|
|
| |
0 |
|
|
|
|
|
|
| |||
2. | Press and hold the Audio |
|
|
|
|
|
|
| ||
S |
|
|
|
|
|
| ||||
| Configuration/Save |
|
|
|
|
|
| |||
| F |
|
|
|
|
|
| |||
| button until the Audio |
|
|
|
|
|
| |||
| Configuration/Save LED |
|
|
|
|
|
|
| ||
| blinks. Release the button. |
| S |
|
|
|
|
| ||
| The Input LEDs indicate |
| F |
|
|
|
|
| ||
| the audio level. The +dB |
|
|
|
|
|
|
| ||
| and |
|
| S |
|
|
|
| ||
| the polarity (+ [gain] or |
|
|
|
|
|
| |||
|
|
| F |
|
|
|
| |||
| – [attenuation]). |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||
| • Each Input LED |
|
|
|
|
|
|
| ||
|
|
|
| S |
|
|
| |||
| shows a range of 3 dB: |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||
| ° Slow blink = 1 dB |
|
|
| F |
|
|
| ||
|
|
|
|
|
|
|
| |||
| ° Fast blink = 2 dB |
|
|
|
|
|
|
| ||
|
|
|
|
| S |
|
| |||
| ° Lit = 3 dB |
|
|
|
|
|
| |||
|
|
|
|
| F |
|
| |||
|
|
|
|
|
|
|
| |||
| • The +dB LED lit |
|
|
|
|
|
|
| ||
| indicates a positive |
| 1 | 2 | 3 | 4 | 5 | 6 | +dB | |
| (gain) level. The |
| ||||||||
| = off, | S | = blinking slowly, |
| ||||||
| F | = blinking fast, | = on |
|
| |||||
| indicates a negative |
|
|
|
|
|
|
|
| |
| (attenuation) level. Both LEDs lit indicate 0 dB. | |||||||||
3. | Press and release the >(Input 5) or <(Input 6) buttons to | |||||||||
| increase or decrease the audio level by 1 dB. |
|
|
| ||||||
4. | Press and hold the Audio Configuration/Save button until | |||||||||
| the Audio Configuration/Save LED goes out. Release the | |||||||||
| button. |
|
|
|
|
|
|
|
|
N• There is one audio gain or attenuation setting per input. The setting is shared by the left and right audio inputs.
•The input audio gain or attenuation settings are stored in
| SW6 VGA Audio • Installation and Operation |