Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic Two, Introduction, cont’d Application Diagrams, YCS SW2 Introduction, Extron

Models: YCS SW2

1 17

Download 17 pages 41.02 Kb

Page 7

Introduction, cont’d

Introduction, cont’d

Application Diagrams

The following diagrams provide examples of how the YCS SW2 may be connected.

VCR
Camera				S-video	Projector
Camera
Video
				Extron
S-video				YCS SW2
		YC	S SW2	YCS SW2
		YC		Two Input, Three Output
				Two Input, Three Output
	TS	PUT		Transcoding Switcher
	OUT
INPU
		C
ER
POW
	2

Video

VCR

Figure 1-1 — Connecting the YCS SW2 to a single- video-input projector and two input devices

	Extron
	MPS 112CS
	Media Presentation
	Switcher
						S-video	Projector
Video
S-video						Extron
				YC	S SW2	Extron
		UTP	UT		AUTO-SW	YCS SW2
		UTP		ACT		Video Decoder/
	O			CONT
INP	UTS			2
INP				1		Switcher/TBC
						Switcher/TBC

POWER
12V	MAX
0.3A	2

Figure 1-2 — Connecting the YCS SW2 to a multi- format switcher

YCS SW2

Chapter2Two

Installation and Operation

Installation Overview

Mounting the YCS SW2

Rear Panel Features

Wiring the Power Connector

Wiring the Captive Screw Connector

Contact Closure

Autoswitching

Front Panel Features

Selecting an Input by Using the Buttons

1-4 YCS SW2 • Introduction

Image 7

Extron electronic YCS SW2 Two, Introduction, cont’d Application Diagrams, Rear Panel Features Wiring the Power Connector

Contents

68-1110-01 Rev. A 2 Input Transcoding SwitcherYCS SW2 User’s ManualSafety Instructions English PrecautionsExtron’s Warranty FCC Class A Notice Appendix A Speciﬁcations, Part Numbers, and Table of ContentsChapter Two Installation Overview YCS SW2 Table of ContentsChapter1One Table of Contents, cont’dAbout this Manual About the YCS SW2 Features Application Diagrams ii YCS SW2 Table of ContentsAbout the YCS SW2 FeaturesIntroduction About this ManualWiring the Captive Screw Connector Contact Closure Autoswitching Introduction, cont’d Application DiagramsInstallation and Operation Installation Overview Mounting the YCS SW2 Rear Panel Features Wiring the Power ConnectorMounting the YCS SW2 Installation and OperationInstallation Overview YCS SW2 Installation and OperationFigure 2-3 - Mounting a YCS on a 6-inch rack shelf Installation and Operation, cont’dBack of the rack mounting Figure 2-2 - Mounting a YCS SW2 on a standard rack shelfFigure 2-5 - Mounting the YCS SW2 to a back rack support 2-6 YCS SW2 Installation and OperationFurniture mounting Projector mountingPMK 250 does not slide down the ceiling pole. A socket Power SupplyPMK 250 Projector Mount Kit Be sure to tighten the hex nuts securely enough that theFigure 2-10 - YCS SW2 rear panel Rear Panel Features2-10 YCS SW2 Installation and Operation PMK 300 Projector Mount KitStripping the wires to expose less than the Wiring the Power ConnectorWiring the Captive Screw Connector 2-12 YCS SW2 Installation and Operation2-14 YCS SW2 Installation and Operation Installation and Operation, cont’d Contact ClosureAutoswitching Front Panel Features2-16 YCS SW2 Installation and Operation Speciﬁcations, Part Numbers and AccessoriesSelecting an Input by Using the Buttons Speciﬁcations Included Parts AccessoriesSpeciﬁcations Speciﬁcations, Part Numbers, and AccessoriesYCS SW2 Speciﬁcations, Part Numbers, and Accessories YCS SW2 Speciﬁcations, Part Numbers, and AccessoriesA-4 YCS SW2 Speciﬁcations, Part Numbers, and Accessories Speciﬁcations, Part Numbers, Accessories, cont’d Included PartsAccessories Accessories