READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD

READ AND SAVE THESE INSTRUCTIONS

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè). Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING: SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN - You may be burned. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. Use an extinguisher ONLY if:

1.You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to an exit.

CAUTION: To Reduce The Risk Of Fire And Electric Shock, Install This RangeHood Only With Remote Blower Models Rated Maximum. 4,2 A suitable for use with solid stade speed controls.

WARRANTY & SERVICE

This rangehood carries a limited warranty against manufacturer’s defects. To obtain warranty service, contact the dealer from whom you purchased the rangehood, or the local Faber distributor. If you cannot identify a local Faber distributor, contact Faber USA at (508) 358-5353 for the name of a distributor in your area.

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area. This unit also has several features to insure operator safety.

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or floor opening around the cap. Flexible ductwork is not recommended. If it is used, each foot of flexible ductwork used is equivalent to two feet of straight metal ductwork when calculating the ductrun length. Thus, a flexible elbow equals two standard elbows.

Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed. For best results, remote blowers should transition to 10" round duct as soon as possible. If small ducting is used, it should be transitioned to 9 or 10" round as soon as possible.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

!WARNING

•Venting system MUST terminate outside the home.

•DO NOT terminate the ductwork in an attic or other enclosed space.

•DO NOT use 4" laundry-type wall caps.

•Flexible-type ductwork is not recommended.

•DO NOT obstruct the flow of combustion and ventilation air.

•Failure to follow venting requirements may result in a fire.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as specified on the serial/ rating plate located inside the unit near the field wiring compartment. THIS UNIT MUST BE CONNECTED WITH COPPER

WIRE ONLY. Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

EN

 

3

Page 2 Page 4
Page 3
Image 3
Faber Remote Blower instruction manual Warranty & Service, USE and Care Information, Electrical Requirements
Page 2 Page 4

Remote Blower specifications

The Faber Remote Blower is a cutting-edge solution designed to enhance the efficiency, performance, and aesthetics of kitchen ventilation systems. Renowned for its innovative engineering, this remote blower system offers numerous features that make it a preferred choice among discerning homeowners and culinary enthusiasts.

One of the primary features of the Faber Remote Blower is its quiet operation. The advanced sound-reduction technology ensures that the blower operates at minimal noise levels, allowing for an uninterrupted cooking experience. This is particularly beneficial in open floor plan designs where kitchen sounds can easily travel to living or dining areas.

Another distinctive characteristic is the blower’s powerful performance. Faber remote blowers are engineered to deliver exceptionally high air extraction capabilities. This means they can effectively eliminate smoke, odors, and other airborne contaminants, ensuring a cleaner and healthier kitchen environment. The blower's adjustable speed settings allow users to fine-tune the extraction power according to their cooking needs, promoting versatility and efficiency.

The Faber Remote Blower also boasts a sleek and minimalist design that blends seamlessly with the overall kitchen aesthetic. Its compact design allows for flexible installation options, including placement in various locations such as the attic or on a roof, completely disentangling the blower from the visual aspect of kitchen appliances. This is particularly appealing to modern homeowners who seek to maintain a clean and elegant appearance in their spaces.

In terms of technology, the Faber Remote Blower integrates smart features such as remote control operation, allowing users to adjust settings from a distance conveniently. Many models include an automatic shut-off feature, which activates after a set period, promoting energy conservation and ease of use.

Furthermore, the build quality of Faber Remote Blowers emphasizes durability and longevity. Constructed with high-grade materials, these blowers are designed to withstand the rigors of daily use while providing consistent performance over time.

In summary, the Faber Remote Blower stands out for its silent yet powerful operation, stylish design, and advanced technological features that enhance the overall cooking experience. With a focus on efficiency and aesthetic appeal, this remote blower is an excellent investment for anyone looking to elevate their kitchen ventilation system. Whether you're an avid home cook or simply want a more pleasant kitchen environment, the Faber Remote Blower is an exceptional choice that meets diverse needs and preferences.
Top Page Image Contents