Field Controls TM-2000 manual

HUMIDIFIER ADJUSTMENT

The TM-2000 must now be adjusted so that it activates after heated air circulation begins, and de-activates before the heated air circulation ends.

1.Turn the adjustment knob on the Housing Assembly to the lowest sensitivity setting (fully clockwise). Set the Housing Assembly power switch to the “ON” position. THE TM-2000 SHOULD NOT ACTIVATE AT THIS TIME.

2.Set the furnace thermostat to cause continued operation of the furnace.

3.At approximately 2 minutes after the furnace begins blowing heated air through the ductwork, turn the adjustment knob counterclockwise just until the TM-2000 activates. This will be indicated by glowing of the “ON” light on the Housing Assembly.

4.Lower the thermostat to end the furnace heating cycle. Check to be sure the TM-2000 deactivates at least 30 seconds before the furnace stops blowing air through the ductwork. If the TM-2000 does not deactivate soon enough, turn the adjustment knob slightly clockwise.

5.Check the operation of the TM-2000 for several more heating cycles to be sure of proper operation as described above, and adjust the TM-2000 as necessary. If proper operation cannot be obtained, call Field Controls Customer Service at (252) 522-3031 for further assistance.

6.Once proper adjustment has been made, humidity levels can be increased or decreased by small adjustments of the TM-2000. Always verify proper operation as described above, after any adjustment has been made.

7.Inspect the system for leaks, loose wires, etc. SEVERAL DROPS OF WATER PER HEATING CYCLE FROM THE DRAIN TUBE ARE NORMAL. IF SIGNIFICANTLY MORE IS OBSERVED, CALL FIELD CONTROLS CUSTOMER SERVICE, OR CONSULT THE TROUBLESHOOTING GUIDE IN THIS MANUAL.

WHEN HUMIDIFICATION IS REQUIRED

1.Plug the transformer into the receptacle.

2.Open the saddle valve completely.

3.Place the "ON/OFF" switch in the "ON" position.

4.Check for proper sequence of operation by setting thermostat to call for heat and follow through complete cycle.

NOZZLE CAPACITY CHART

Table 1

NOZZLE

SIZE

PART

NUMBER

HEATED GAL/DAY FLOOR SPACE

STD/OPT

0.65		46017401		UP TO 9	UP TO	STANDARD
0.65					3000
	GPH				3000
	GPH				SQ. FT.
					SQ. FT.
1.00					UP TO
1.00		46017402		UP TO 12	4000	OPTIONAL
	GPH	46017402		UP TO 12	4000	OPTIONAL
	GPH				SQ. FT.
					SQ. FT.
1.35					UP TO
1.35		46017403		UP TO 18	5000	OPTIONAL
	GPH	46017403		UP TO 18	5000	OPTIONAL
	GPH				SQ. FT.
					SQ. FT.
ELECTRICAL RATING
Table 2

	VOLTS		AMPS		VA	Hz
	24 VAC		0.40		10	60

Page 5

TM-2000 specifications

The Field Controls TM-2000 is a sophisticated air management system designed to enhance indoor air quality and energy efficiency in residential and commercial buildings. This advanced system employs cutting-edge technologies to ensure optimal performance and user-friendly operations.

One of the main features of the TM-2000 is its ability to effectively reduce airborne contaminants, including dust, allergens, and volatile organic compounds (VOCs). By utilizing a combination of mechanical filtration and advanced air purifying technologies, the TM-2000 helps create a healthier indoor environment. The system is equipped with a high-efficiency filter that captures particulate matter as small as 0.3 microns, ensuring that even the smallest pollutants are removed from the air.

The TM-2000 is designed with smart technology that allows for seamless integration with existing HVAC systems. It features a user-friendly interface that provides real-time monitoring of air quality levels, filter status, and system performance. This allows homeowners and building managers to stay informed and make necessary adjustments to maintain optimal indoor air quality.

Another key characteristic of the TM-2000 is its energy-efficient operation. The unit is engineered to minimize energy consumption while delivering powerful air purification. It incorporates programmable settings, allowing users to tailor operation times and intensity based on their schedules and the specific air quality needs of their spaces. This not only conserves energy but also reduces utility costs, making it an economical option for users.

The TM-2000 also stands out in its versatility. It is suitable for a wide range of applications, from residential homes to office buildings and industrial facilities. Its compact design enables easy installation and maintenance, making it user-friendly for both professionals and end-users.

Safety features are also integrated into the TM-2000, including automatic shutoff capabilities and indicators for filter replacement. These safeguards ensure that the system operates efficiently and protects both the unit and its users.

In conclusion, the Field Controls TM-2000 is a state-of-the-art solution for anyone looking to improve indoor air quality. With its advanced filtration technology, user-friendly interface, energy-efficient operation, and robust safety features, it represents a smart investment for healthier living and working environments.

Field Controls TM-2000 Nozzle Size Part Number Heated GAL/DAY Floor Space STD/OPT

Models: TM-2000