(2,1)
4PARTS SUPPLIED
Drain hose | Drain hose | Wire clip (1) | Side mounting | Top mounting | Clamp (1) | Phillips | 1½” (38 mm) | Rubber | Cavity bracket | Moisture protection |
support (1) | joiner (1) |
| bracket kit | brackets (2) |
| 5⁄8” (16 mm) | bottom | washer for | kit (1) | tape (1) |
|
|
| (A and B) (2) | OPTIONAL |
| screws (7) | fixing screws | inlet hose (1) | (supplied only with | (to prevent moisture |
|
|
| OPTIONAL |
|
|
| & metal |
| Prefinished flat door | damage) |
|
|
|
|
|
|
| washers (2) |
| and Integrated models) |
|
Edge protector (1) (if services hole partition is metal)
If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 11’ 10” (3.6m). The kit is available from the nearest Fisher & Paykel Authorized Service Agent, or Toll free 1.888.936.7872 or www.fisherpaykel.com.
5 CAVITY PREPARATION
Important!
Be sure the edges of the services hole are smooth or covered. If the services hole is through a metal partition the hole must be protected with the Edge protector supplied to prevent damage to the power cord or hoses.
These marks indicate formed bracket screw locations.
Note: To align drawer front to adjacent cabinetry, the product to countertop clearance can
be increased to 1⁄8” (3 mm).
*Preferred position. If adequate clearance, services hole can be higher.
If hole is higher, ensure drain hose(s) are routed straight into the waste connection.
Water Connection
Recommended HOT (Maximum 140°F/60°C).
Supplied hose to suit 3/8” (9 mm) male compression fitting.
If no side partition, use a brace for securing.
2” x 4”
Moisture 3⁄8” protection
(10 mm) tape must be applied.
|
|
| can | be | located | |
| Services | . | ||||
Note: |
| |||||
|
| |||||
side | of DishDrawer® | |||||
either | ||||||
|
|
|
| |||
|
|
|
|
| ||
Water Pressure | Max | Min |
Water softener models | 1 MPa (145 psi) | 0.1 MPa (14.5 psi) |
Other models | 1 MPa (145 psi) | 0.03 MPa (4.3 psi) |
Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations.
max. ø 1 ½” (38 mm)
* | * |
|
| max. 17 11⁄16” |
|
| (450 mm) | Water supply |
Max. distance of | Left hand | Right hand | |
hoses and cord from | |||
side | side | ||
chassis edge | |||
|
| ||
Drain hose | 78 ½” | 70 ½” | |
| (2000 mm) | (1800 mm) | |
|
|
| |
Inlet hose | 64 ¾” | 49” | |
| (1650 mm) | (1250 mm) | |
|
|
| |
Power cord (excl. plug) | 29 ½” | 27 ½” | |
| (750 mm) | (700 mm) | |
|
|
|
Left hand
side
Right hand
side
|
| min. 7 7⁄8” |
|
| (200 mm) |
|
| |
Important! | ||
| Adjacent cabinetry must not | max. 15 A |
| extend above cavity base |
|
