Friedrich 920-087-04 (3-05) Electrical Rating Tables, Power Cord Information 230/208V models only

920-087-04 (3-05)

A. Electrical Rating Tables

All230/208voltunitsareequippedwithpowercords.SeeAppendixBonpage19forwiringinstructionson265Vunits.

NOTE: Use Copper Conductors ONLY. Wire sizes are per NEC, check local codes for overseas applications.

Table 1	250 V Receptacles and Fuse Types
AMPS		15	20*	30
RECEPTACLE
TIME-DELAY TYPE FUSE		15	20	30
(or HACR circuit breaker)

HACR – Heating, Air Conditioning, Refrigeration

*May be used for 15 Amp applications if fused for 15 Amp NOTE: 265 volt units are hard wired.

Table 2	Recommended branch circuit wire sizes*
NAMEPLATE / MAXIMUM		AWG WIRE SIZE**
CIRCUIT BREAKER SIZE
	15	14
	20	12
	30	10

AWG – American Wire Gauge * Single circuit from main box

** Based on copper wire, single insulated conductor at 60°C

ELECTRIC SHOCK HAZARD! Turn off electric power before service or installation. All electrical connections and wiring MUST be installed by a qualified electrician and conform to the National Electrical Code and all local codes which have jurisdiction. Failure to do so can result in property damage, personal injury and/or death.

WIRE SIZE	Use ONLY wiring size recommended for
	single outlet branch circuit.
	Use ONLY type and size fuse or HACR cir-
FUSE/CIRCUIT	cuit breaker indicated on unit’s rating plate.
	Proper current protection to the unit is the
BREAKER
	responsibility of the owner. NOTE: A time
	delay fuse is provided with 265V units.
	Unit MUST be grounded from branch circuit
	through service cord to unit, or through sep-
	arate ground wire provided on permanently
	connected units. Be sure that branch circuit
GROUNDING	or general purpose outlet is grounded. The
	field supplied outlet must match plug on
	service cord and be within reach of service
	cord. Refer to Table 1 for proper receptacle
	and fuse type. Do NOT alter the service cord
	or plug. Do NOT use an extension cord.
	The field supplied outlet must match plug on
RECEPTACLE	service cord and be within reach of service
	cord. Refer to Table 1 for proper receptacle
	and fuse type. Do NOT alter the service cord
	or plug. Do NOT use an extension cord.
	Use recommended wire size given in Table
WIRE SIZING	2 and install a single branch circuit. All wiring
	must comply with local and national codes.
	NOTE: Use copper conductors only.

B. Power Cord Information (230/208V models only)

All Friedrich 230/208V PTAC units are shipped from the factory with a Leakage Current Detection Interrupter (LCDI) equipped power cord. The LCDI device meets the UL and NEC requirements for cord connected air conditioners effective August 2004.

To test your power supply cord:

1.Plug power supply cord into a grounded 3 prong outlet.

2.Press RESET.

3.Press TEST (listen for click; Reset button trips and pops out).

4.Press and release RESET (listen for click; Reset button latches and remains in). The power supply cord is ready for operation.

Figure10a 4.1"

15/20A LCDI Device

2"	RESET	TEST
		Test Button
		Reset Button

NOTE: The LCDI device is not intended to be used as a switch.

Once plugged in the unit will operate normally without the need to reset the LCDI device. If the LCDI device trips and requires resetting the cause of the trip should be identified prior to further use of the PTAC.

If the device fails to trip when tested or if the power supply cord is damaged it must be replaced with a new supply cord obtained from the product manufacturer, and must not be repaired.

Figure10b

30A LCDI Device

7"

2"

Test Button

Reset Button

13