Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MAP3735FC manual Installation, Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives

Models: MAP3735FC MAP3147FC

1 114

Download 114 pages 6.14 Kb

Page 63

CHAPTER 5 Installation

a) Do not give the drive shocks or vibrations exceeding the value defined in the standard because it may cause critical damage to the drive. Especially be careful when unpacking.

b) Do not leave the drive in a dirty or contaminated environment.

c) Since static discharge may destroy the CMOS semiconductors in the drive, note the following after unpacking:

• Use an antistatic mat and body grounding when handling the drive.

• Hold the DE when handling the drive. Do not touch PCAs except for setting.

Hot temperature

To prevent injury, do not handle the drive until after the device has cooled sufficiently after turning off the power. The DE and LSI become hot during operation and remain hot immediately after turning off the power.

CHAPTER 5 Installation

5.1Notes on Handling Drives

5.2Setting

5.3Mounting Drives

5.4Dismounting Drives

5.5Checking Operation after Installation and Preparing the IDD for Use

5.6Spare Disk Drive

This chapter describes the notes on handling drives, setting, mounting drives, confirming drive operations after installation and preparation for use, and dismounting drives.

5.1Notes on Handling Drives

The items listed in the specifications in Table 2.1 must be strictly observed.

(1)General notes

C141-E163

5-1

Image 63

Fujitsu MAP3735FC, MAP3147FC Installation, Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives, Dismounting Drives

Contents

C141-E163-01EN MAP3147FC MAP3735FC DISK DRIVES PRODUCT/MAINTENANCE MANUALFOR SAFE OPERATION Handling of This ManualIMPORTANT NOTE TO USERS Chapter 5 Installation PrefaceChapter 2 Specifications Chapter 4 Installation RequirementsPreface APPENDIX AConventions for Alert Messages CONVENTIONS USED IN THIS MANUAL PrefaceThis page is intentionally left blank Important Alert Messages Important Alert ItemsC141-E163 Important Alert ItemsImportant Alert Items C141-E163This page is intentionally left blank Manual Organization This page is intentionally left blank REFERENCED STANDARDS FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE FC-PHFIBRE CHANNEL PRIVATE LOOP SCSI DIRECT ATTATH FC-PLDA This page is intentionally left blank Alternate block allocation CONTENTSContents A.1 Interface FC-SCA Connector Signal Allocation Illustrations ContentsFigures Tables ContentsThis page is intentionally left blank 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration CHAPTER 1 General DescriptionGeneral Description 1.1 Standard Features1.1 Standard Features 12 Automatic alternate block reassignment General Description1.2 Hardware Structure 1.2 Hardware StructureFigure 1.1 FC model drives outer view General Description Disk/head configuration1.3 System Configuration 1.3 System ConfigurationFigure 1.3 Example of FC-AL system configuration General Description 1 Loop configurationTable 2.1 Model names and order numbers CHAPTER 2 Specifications2.1 Hardware Specifications 2.1 Hardware Specifications 2.1.1 Model name and order numberSpecifications 2.1.2 Function specificationsFunction specifications 2.1 Hardware Specifications Seek time ms Seek Difference 2048 Cyl/div5 This value indicates at ready mode C141-E163 Specifications2.1.3 Environmental specifications Environmental/power requirements2.1 Hardware Specifications 2.1.4 Error rate2.1.5 Reliability The MTBF is defined as Operating time hours at all field sites MTBF= Specifications2.1 Hardware Specifications 4 Data security at power failureC141-E163 This page is intentionally left blank 3.3 Defect Management CHAPTER 3 Data Format3.1.1 Cylinder configuration 3.1 Data Space 3.2 Logical Data Block AddressingData Format Figure 3.1 Cylinder configurationZone layout and track capacity 3.1 Data Space3.1.2 Alternate spare area Data Format3.1.3 Track format 3.1 Data SpaceFigure 3.2 Spare area in cell Figure 3.3 Alternate cylinderFigure 3.4 Track format Data FormatFigure 3.6 Sector format 3.1 Data SpaceFigure 3.5 Track skew/head skew 3.1.4 Sector formatEach sector on the track consists of the following fields Data Format3.2 Logical Data Block Addressing 3.2 Logical Data Block Addressing3.1.5 Format capacity Table 3.2 Format capacity1 Block address of user space Data Format3.3 Defect Management 3.3 Defect Management 3.3.1 Defect list3.3.2 Alternate block allocation Data Format Figure 3.7 Alternate block allocation by FORMAT UNIT command3-13 Figure 3.8 Alternate block allocation by REASSIGN BLOCKS command3.3 Defect Management C141-E1633 Automatic alternate block allocation Data Format3.3 Defect Management Automatic alternate block allocation is made only once during the execution of one command. If second defective block is detected, the alternate block assignment processing for the first defective block is executed but the alternate block assignment processing for the second one is not executed and the command being executed terminates. However, the initiator can recover the twice error by issuing the same command againThis page is intentionally left blank 4.3 Connection Requirements CHAPTER 4 Installation Requirements4.1 Mounting Requirements 4.2 Power Supply Requirements 4.1 Mounting Requirements 4.1.1 External dimensionsFigure 4.1 External dimensions Installation Requirements4.1 Mounting Requirements 4.1.2 MountingFigure 4.2 IDD orientations 4.1.3 Notes on mounting Installation Requirements Figure 4.3 Mounting frame structureFigure 4.4 Limitation of side-mounting Table 4.1 Surface temperature check point Figure 4.5 Surface temperature measurement points4.1 Mounting Requirements Figure 4.6 Service clearance area Installation Requirements4.2 Power Supply Requirements 4.2 Power Supply RequirementsFigure 4.7 Current waveform +12 VDC Figure 4.8 AC noise filter recommended Installation Requirements5 Noise filter Attenuation 40 dB or more at 10 MHz4.3 Connection Requirements 4.3.1 Connector Figure 4.9 Connector location 4.3.2 Interface connector4.3 Connection Requirements C141-E163 Installation RequirementsFigure 4.10 SCA2 type connector 4-105.6 Spare Disk Drive CHAPTER 5 Installation5.1 Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives 5.4 Dismounting DrivesInstallation Motor start mode 5.2 Setting5.2 Setting 5.2.1 Loop ID setting 5.2.2 Mode settings5.3 Mounting Drives 5.3.1 Mounting procedures Installation5.4 Dismounting Drives 5.4 Dismounting DrivesInstallation C141-E1635.5.1 Checking initial operation 5.5.2 Checking connection Installation Motor starts when power is turned onFigure 5.1 Checking the IDD connection A Figure 5.2 Checking the IDD connection B Motor starts by START/STOP command Executing time about 60 seconds5.5.3 Formatting Installation2 FORMAT UNIT command 5.5.4 Setting parameters Installationcontinued Installation 5-14C141-E163 C141-E163 5-15absolute value 5.6 Spare Disk Drive Installation5-16 C141-E1636.1 Diagnostics 6.1.1 Self-diagnostics CHAPTER 6 Diagnostics and Maintenance6.1 Diagnostics 6.2 Maintenance Information 6.3 Operation Check 6.4 Troubleshooting ProceduresDiagnostics and Maintenance Operation of self-diagnostics 6.1 Diagnostics6.1.2 Test programs Diagnostics and Maintenance6.2 Maintenance Information 6.2.1 Precautions 6.2 Maintenance InformationPreventive maintenance such as replacing air filters is not required Diagnostics and Maintenance6.2.2 Maintenance requirements 1 Preventive maintenance3 Parts that can be replaced in the field 6.2 Maintenance Information6.2.3 Maintenance levels Diagnostics and Maintenance6.2 Maintenance Information 6.2.4 Revision numbersFigure 6.1 Revision label example Diagnostics and Maintenance Figure 6.2 Indicating revision numbers 6.2.5 Tools and test equipment6.2.6 Tests 6-11 6.2 Maintenance InformationFigure 6.3 Test flowchart C141-E1636.3.2 Operation test Diagnostics and Maintenance6.3.3 Diagnostic test 6.3 Operation Check 6.3.1 Initial seek operation check6.4.2 Troubleshooting with disk drive replacement in the field 6.4 Troubleshooting Procedures6.4 Troubleshooting Procedures 6.4.1 Outline of troubleshooting proceduresSystem-level field troubleshooting Diagnostics and MaintenanceC141-E163 6.4 Troubleshooting Procedures6.4.3 Troubleshooting at the repair site Disk drive troubleshooting6.4.5 Finding possibly faulty parts Diagnostics and Maintenance6.4.4 Troubleshooting with parts replacement in the factory This manual does not cover troubleshooting at the factory level7.1.2 Sense key, sense code, and subsense code CHAPTER 7 Error Analysis7.1 Error Analysis Information Collection 7.2 Sense Data Analysis 7.1 Error Analysis Information Collection 7.1.1 Sense dataFigure 7.1 Format of extended sense data Error AnalysisDefinition of sense data 7.2.1 Error information indicated with sense data7.2 Sense Data Analysis 7.2 Sense Data Analysis7.2.2 Sense data 3-0C-03, 4-40-xx, 4-44-xx, and 4-C4-xx Error Analysis7.2.3 Sense data 1-1x-xx, 3-1x-xx and E-1D-00 Disk read error C141-E163A.1 Interface FC-SCA Connector Signal Allocation APPENDIX A Connector Signal AllocationTable A.1 Connector Signal AllocationA.1 Interface FC-SCA Connector Signal Allocation FC-SCA connector CN1Initiator INIT GlossaryCommand FC DeviceTarget TARG GlossaryAcronyms and Abbreviations Acronyms and Abbreviations Index Index Index This page is intentionally left blank 1, Place des Etats-Unis, SILIC 310, 94588 Rungis Cedex, FRANCE This page is intentionally left blank FOR FUJITSU USE READER’S COMMENT FORMThis page is intentionally left blank