Interface

5.5 Ultra DMA Feature Set

5.5.1 Overview

Ultra DMA is a data transfer protocol used with the READ DMA and WRITE DMA commands. When this protocol is enabled it shall be used instead of the Multiword DMA protocol when these commands are issued by the host. This protocol applies to the Ultra DMA data burst only. When this protocol is used there are no changes to other elements of the ATA protocol (e.g.: Command Block Register access).

Several signal lines are redefined to provide new functions during an Ultra DMA burst. These lines assume these definitions when 1) an Ultra DMA Mode is selected, and 2) a host issues a READ DMA or a WRITE DMA, command requiring data transfer, and 3) the host asserts DMACK-. These signal lines revert back to the definitions used for non-Ultra DMA transfers upon the negation of DMACK- by the host at the termination of an Ultra DMA burst. All of the control signals are unidirectional. DMARQ and DMACK- retain their standard definitions.

With the Ultra DMA protocol, the control signal (STROBE) that latches data from DD (15:0) is generated by the same agent (either host or device) that drives the data onto the bus. Ownership of DD (15:0) and this data strobe signal are given either to the device during an Ultra DMA data in burst or to the host for an Ultra DMA data out burst.

During an Ultra DMA burst a sender shall always drive data onto the bus, and after a sufficient time to allow for propagation delay, cable settling, and setup time, the sender shall generate a STROBE edge to latch the data. Both edges of STROBE are used for data transfers so that the frequency of STROBE is limited to the same frequency as the data. The highest fundamental frequency on the cable shall be 16.67 million transitions per second or 8.33 MHz (the same as the maximum frequency for PIO Mode 4 and DMA Mode 2).

Words in the IDENTIFY DEVICE data indicate support of the Ultra DMA feature and the Ultra DMA Modes the device is capable of supporting. The Set transfer mode subcommand in the SET FEATURES command shall be used by a host to select the Ultra DMA Mode at which the system operates. The Ultra DMA Mode selected by a host shall be less than or equal to the fastest mode of which the device is capable. Only the Ultra DMA Mode shall be selected at any given time. All timing requirements for a selected Ultra DMA Mode shall be satisfied. Devices supporting Ultra DMA Mode 2 shall also support Ultra DMA Modes 0 and 1. Devices supporting Ultra DMA Mode 1 shall also support Ultra DMA Mode 0.

An Ultra DMA capable device shall retain its previously selected Ultra DMA Mode after executing a Software reset sequence. An Ultra DMA capable device shall clear any previously selected Ultra DMA Mode and revert to its default non- Ultra DMA Modes after executing a Power on or hardware reset.

5-92

C141-E104-02EN

Page 169
Image 169
Fujitsu MHM2100AT, MHM200AT, MHM215OAT, MHL2300AT manual Ultra DMA Feature Set, Overview

MHM215OAT, MHM200AT, MHL2300AT, MHM2100AT specifications

Fujitsu, a leader in storage technology, has developed a range of hard disk drives designed for reliability and performance, catering to both enterprise and consumer needs. The Fujitsu MHM2100AT, MHL2300AT, MHM200AT, and MHM215OAT models are part of this impressive lineup, showcasing various features and technologies that set them apart.

The MHM2100AT model is known for its 2.5-inch form factor, offering a storage capacity of 100GB. It operates at a speed of 5400 RPM, which balances performance and power efficiency. The drive utilizes ATA-6 interface (Parallel ATA) ensuring compatibility with a wide range of systems. One of its primary features is the advanced cache memory architecture, which allows for quicker access to frequently used data. This enhances overall system performance while preserving energy consumption.

The MHL2300AT provides a step up, with its 300GB of capacity. It also maintains a 5400 RPM speed and is designed for optimal heat dissipation and durability. This model is particularly suited for mobile computing applications due to its lightweight design and low power requirements. The MHL2300AT also integrates a sophisticated error correction code (ECC) technology, enhancing data integrity during storage and retrieval processes.

Moving on to the MHM200AT, this unit provides substantial storage of 200GB, maintaining a similar 5400 RPM speed. What sets the MHM200AT apart is its focus on data security with Built-in Security Features such as disk encryption capabilities. This model is suitable for professionals dealing with sensitive information, ensuring both performance and protection against data breaches.

Lastly, the MHM215OAT, another key model, balances user-friendly design with performance metrics. It offers a generous 150GB capacity and features an enhanced seek time for quick file access. With its emphasis on reliability, the MHM215OAT is often utilized in environments where uptime is critical, such as in commercial servers or high-performance workstations.

In conclusion, Fujitsu's MHM2100AT, MHL2300AT, MHM200AT, and MHM215OAT each possess unique features and technologies that cater to diverse user needs. Their combination of efficient power consumption, enhanced data integrity, and reliability make them compelling choices for businesses and individuals alike. Whether for mobile devices, personal computing, or enterprise applications, these models continue to exemplify Fujitsu's commitment to quality and performance in storage solutions.