Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MHV2040BH, MHV2120BH, MHV2100BH, MHV2080BH, MHV2060BH manual Read DMA X’C8’ or X’C9’

Models: MHV2100BH MHV2040BH MHV2120BH MHV2060BH MHV2080BH

1 276

Download 276 pages 27.07 Kb

Page 158

Interface

(21) READ DMA (X’C8’ or X’C9’)

The READ DMA command reads data from sectors, starting from the sectors specified in the Device/Head, Cylinder High, Cylinder Low, and Sector Number fields and continuing for as many sectors as specified in the Sector Count field. A value ranging from 1 to 256 can be specified for the number of sectors. In order to specify 256, "00" must be set in the Sector Count field. For the protocol concerning data transfers, see Section 5.4.4.

When the command is completed, either cylinder, head, and sector addresses (CHS mode) or the logical block address (LBA mode) of the last sector is stored in the Shadow Block Register.

If an error such as an uncorrectable disk read error is detected during execution of the READ DMA command and continued operation not possible, the data transfer stops after all data, including the data of the sector where the error was detected, is transferred. The device notifies the host of the status by sending the RegDH FIS. At this time, the number of remaining sectors including the sector where the error was detected, and either cylinder, head, and sector addresses (CHS mode) or the logical block address (LBA mode) of the sector where the error was detected are stored in the Shadow Block Register.

The host system can select the DMA transfer mode by using the SET FEATURES command, however, the transfer speed does not change.

•Multiword DMA transfer mode 0 to 2

•Ultra DMA transfer mode 0 to 5

•Error reporting conditions

(1)A specified address exceeds the range where read operations are allowed (ST = 51h, ER = 10h).

(2)The range where read operations are allowed will be exceeded by an address during a read operation (ST = 51h, ER = 10h).

(3)An uncorrectable disk read error occurred (ST = 51h, ER = 40h).

(4)The sync byte indicating the beginning of a sector was not found (ST = 51h, ER = 01h).

(5)A SATA communication error occurred (ST = 51h, ER = 0Ch).

(6)A Host Buffer CRC error occurred (ST = 51h, ER = 84h).

(7)An error other than the above errors occurred (ST = 51h, ER = 04h).

5-84

C141-E224

Image 158

Fujitsu MHV2040BH, MHV2120BH, MHV2100BH, MHV2080BH, MHV2060BH manual Read DMA X’C8’ or X’C9’

Contents

MHV2120BH, MHV2100BH, MHV2080BH MHV2060BH, MHV2040BH Disk Drives Product Manual For Safe Operation Handling of This Manual Revision History This page is intentionally left blank Preface Overview of Manual Conventions Conventions for Alert MessagesOperating Environment Liability Exception This page is intentionally left blank Important Alert Items Important Alert Messages This page is intentionally left blank Disk Drives Product Manual Disk Drives Maintenance ManualManual Organization This page is intentionally left blank Contents Theory of Device Operation Device ConfigurationInstallation Conditions Contents Interface Xii C141-E224 104 Acronyms and Abbreviations AB-1 OperationsGL-1 IN-1 Illustrations Figures Response to power-on Tables Examples of model names and product numbers 133 Device Overview Adaptability FeaturesFunctions and performance High resistance against shock Error correction and retry by ECCLow noise and vibration Connection to Sata interface Specifications 1/2 Device SpecificationsSpecifications summary Model and product number Examples of model names and product numbers Ripple Power RequirementsInput Voltage Slope of an input voltage at rise Negative voltage at +5 V when power is turned off Current Requirements and Power Dissipation Current and power dissipation Power on/off sequence Environmental SpecificationsCurrent fluctuation Typ. at +5 V when power is turned on Environmental specifications Acoustic Noise Acoustic noise specificationShock and vibration specification Shock and Vibration Mean time to repair Mttr Service lifeData assurance in the event of power failure Positioning error Error RateUnrecoverable read error Media Defects Advanced Power Management APM Recommended power-off sequence Advanced Power Management Device-initiated interface power management Dipm Interface Power Management IPMHost-initiated interface power management Hipm Interface power management Restriction of Use of Hazardous Substances Device Configuration Device Configuration Drive connection System ConfigurationSata interface Read/write circuit This page is intentionally left blank Installation Conditions Dimensions Dimensions Orientation MountingIntegration Guidance C141-E144 PCA FrameLimitation of mounting Location of breather Ambient temperature Service area Handling cautions Hios ESDSumitomo 3M Device connector Connections with Host System Recommended connector specifications for the host system Connector specifications for host systemSignal segment and power supply segment Sata interface cable connection This page is intentionally left blank Theory of Device Operation Disk OutlineSubassemblies Spindle Servo circuit Circuit ConfigurationAir filter Spindle motor driver circuit Power supply configuration PCA Power-on Sequence Power-on operation sequence Self-calibration contents Self-calibration Command processing during self-calibration Execution timing of self-calibration Write circuit Read/write CircuitRead/write preamplifier PreAMP Write precompensation Programmable filter circuit Read circuitAGC circuit D converter circuit Digital PLL circuitFIR circuit Viterbi detection circuit Servo Control Servo control circuit Servo burst capture circuit Power amplifierMicroprocessor unit MPU A converter DAC Driver circuit VCM current sense resistor CSR Data area Data-surface servo formatInner guard band Outer guard band Physical sector servo configuration on disk surface Servo frame format Seek operation Actuator motor controlOperation to move the head to the reference cylinder Track following operation Stable rotation mode Start modeAcceleration mode Spindle motor control This page is intentionally left blank Interface Interface signals Physical Interface 5VDC/GND Comreset / CominitComwake Signal interface regulation Out of band signaling EOF AlignCont Pmack Rrdy RIPROK SOF FER Electrical specificationsPhysical Layer Electrical Requirements 1/3 Physical Layer Electrical Requirements 2/3 Physical Layer Electrical Requirements 3/3 Connector pinouts Connector pinouts Driving Ready LED 5 P11 functionStaggered Spin-up Requirements for P11 as an output pin Example of the circuit for driving Ready LED Hot Plug Conceptual diagram of communication layers Logical Interface Link layer Communication layersPhysical layer Transport layer Outline of the Shadow Block Register Shadow Block Register Register Host to Device Outline of the frame information structure FISFIS types Register Host to Device FIS layout Register Device to Host DMA Active Device to Host DMA Setup Device to Host or Host to Device Bidirectional TAG Bist Active Bidirectional Bist combinations Data FIS Bidirectional layout PIO Setup Device to HostData Host to Device or Device to Host Bidirectional Interface Set Device Bits Device to Host 11 Set Device Bits FIS UNC Error FieldShadow block registers Sfrr Sector Number Field exp Features Field expSector Count Field exp Cylinder Low Field exp HS3 HS2 HS1 HS0 Cylinder High Field expDevice/Head Field HS3 Status field Bit Device Write Fault DF bitBit Error ERR bit Bit 7 Busy BSY bit Device Control Field Command FieldBit 2 Software Reset Srst EStatus Field Command code and parameters 1/3 Host CommandsCommand code and parameters Command code and parameters 2/3 Command code and parameters 3/3 Command descriptions Error reporting conditions Recalibrate X’10’ to X’1F’ Read Sectors X’20’ or X’21’ LBA LSB LBA Write Sectors X’30’ or X’31’ 00 *1 Error information Write Verify X’3C’ Host Commands Read Verify Sectors X’40’ or X’41’ Host Commands Seek X’70’ to X’7F’ Execute Device Diagnostic X’90’ Diagnostic code Initialize Device Parameters X’91’ Download Microcode X’92’ Operation of Download Microcode Error reporting conditions Standby Immediate X’94’ or X’E0’ Interface Unload Feature Unload Immediate Command Standby X’96’ or X’E2’ Idle X’97’ or X’E3’ Interface Check Power Mode X’98’ or X’E5’ ’FF’ Comreset Sleep X’99’ or X’E6’ Smart X’B0’ 10 Features Field values subcommands and functions 1/3 Smart Disable Operations 10 Features Field values subcommands and functions 2/3Smart Enable Operations Smart Read LOG ’DA’ Smart Return Status 10 Features Field values subcommands and functions 3/3’DB’ Smart ENABLE/DISABLE Auto OFF-LINE Key C2h 1FF 12 Format of guarantee failure threshold value data11 Format of device attribute value data Data format version number Attribute ID Attribute value for the worst case so far Status FlagCurrent attribute value Raw attribute value 14 Self-test execution status 13 Off-line data collection statusSelf-test execution status 16 Failure prediction capability flag 17 Drive error logging capability15 Off-line data collection capability Checksum Guarantee failure thresholdSmart error logging 18 Log Directory Data Format 19 Data format of Smart Summary Error Log 1/2 Error data structure 19 Data format of Smart Summary Error Log 2/2Command data structure Total number of drive errors 20 Data format of Smart Comprehensive Error Log Smart Self-Test Self-test number Self-test index Current LBA under test 22 Selective self-test log data structureTest Span Current Span under test Feature Flags23 Selective self-test feature flags Selective Self-test pending time min Device Configuration Freeze Device Configuration XB1Device Configuration Restore Device Configuration Identify Device Configuration Restore Features Field = C0h Device Configuration Freeze Lock Features Field = C1h Device Configuration Identify Features Field = C2h Device Configuration SET Features Field = C3h 24 Device Configuration Identify data structure 1/2 Word Value Content 24 Device Configuration Identify data structure 2/2 Read Multiple X’C4’ 12 Execution example of Read Multiple command LBA LSB Write Multiple X’C5’ At command issuance Shadow Block Registers setting contents SET Multiple Mode X’C6’ Host Commands Read DMA X’C8’ or X’C9’ LBA Write DMA X’CA’ or X’CB’ Host Commands Read Buffer X’E4’ Flush Cache X’E7’ Write Buffer X’E8’ Identify Device X’EC’ Identify Device DMA X’EE’ 25 Information to be read by Identify Device command 1/3 ’3FFF’ 25 Information to be read by Identify Device command 2/3 25 Information to be read by Identify Device command 3/3 MHV2120BH MHV2100BH MHV2080BH MHV2060BH MHV2040BH ’3FFF’ Interface Command without interrupt supports 2, 4, 8 and 16 sectors Interface Host Commands Interface Host Commands Device always returns the fixed value indicated on the left Host Commands SET Features X’EF’ 26 Features field values and settable modes 1/2 26 Features field values and settable modes 2/2 Data Transfer Mode Advanced Power Management APM Serial ATA Functions Automatic Acoustic Management AAM 27 Contents of Security SET Password data Error reporting conditions Security UNLOCKX’F2’ When the master password is selectedWhen the user password is selected Host Commands Security Erase Prepare X’F3’ Security Erase Unit X’F4’ Security Freeze Lock X’F5’ Error reporting conditions 29 Contents of security password Error reporting conditions Read Native MAX Address X’F8’ Lbalsb SET MAX X’F9’ SET MAX Address SET MAX SET Password Features Field = 01h Password information SET MAX Lock Features Field = 02h SET MAX Unlock Features Field = 03h SET MAX Freeze Lock Features Field = 04h Read Sector S EXT X’24’ Description Read DMA EXT X’25’ Description Read Native MAX Address EXT X’27’ Read Multiple EXT X’29’ Read LOG EXT X2F Sector offset 30 Data format of Read Log Ext log page 10h 31 Tag field information 32 Data format of Read Log Ext log page 11h 33 Counter Identifier information Write Sector S EXT X’34’ Description Write DMA EXT X’35’ Description SET MAX Address EXT X’37’ SET MAX LBA Write Multiple EXT X’39’ Write LOG EXT X3F Error information C141-E224 Read Verify Sector S EXT X’42’ Flush Cache EXT X’EA’ Write Multiple FUA EXT XCE Write DMA FUA EXT X3D Read FP DMA Queued Write FP DMA Queued Command Name Error posting34 Command code and parameters 1/2 Sfrw Sfrr DWF 34 Command code and parameters 2/2TK0NF Execute Device Diagnostic Initialize Device Parameters Command ProtocolNon-data command protocol Data Host PIO data-in command protocol PIO data-out command protocol 14 PIO data-in command protocol 15 PIO data-out command protocol DMA data-in command protocol Read DMA EXT Identfy Device Identfy Device DMA DMA data-out command protocol Write DMA EXT FUA EXT Native Command Queuing protocol Read FP DMA Queued Write FP DMA Queued 18 Read FP DMA Queued command protocol 19 Write FP DMA Queued command protocol Power-on and Comreset 20 Power-on sequence 21 Comreset sequence This page is intentionally left blank Operations Reset and Diagnosis Response to power-on Reset and Diagnosis Response to Comreset Response to Comreset Software settings preservation Comreset preservation requirements SET Address MAX EXT Response to a software reset Response to a software reset Active mode Power SavePower save mode Active idle mode Standby mode Sleep mode Power commands Partial mode Power Save Controlled by Interface Power Management IPMPower save mode of the interface Slumber mode MB buffer Read-ahead CacheData buffer structure Data that is a target of caching Commands that are targets of cachingCaching operation Invalidating caching-target data Using the read segment buffer Miss-hit Sequential hit Full hit HAP end location of the previous read command Partial hit Cache operation Command that are targets of cachingWrite Cache Invalidation of cached data Cashing function when power supply is turned on Status report in the event of an errorComreset and software reset response Enabling and disabling This page is intentionally left blank Glossary Master Device Power save modeHost receptacle PIO Programmed input-output Serial-ATA Rotational delaySeek time Slave Device This page is intentionally left blank Acronyms and Abbreviations This page is intentionally left blank Index Caching Index Example of model name and product Mean time between failure Mtbf Read Native MAX Address 4-3 Status, off-line data collection Comment Form Japan This page is intentionally left blank MHV2120BH, MHV2100BH, MHV2080BH, MHV2060BH, MHV2040BH C141-E224-02ENPage