Español Français English

5Still Mode

You can pause the image shown on the TV screen.

Press [STILL] to pause the image shown on the TV screen.

Still

The sound output will not be paused.

If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted.

The still function will be released after 5 minutes.

To cancel still mode, press any button except [POWER].

5Switching Each Input Mode

You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access external devices when they are connected to the unit.

Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes.

 

 

 

 

 

 

DTV/TV channel

 

 

 

 

 

 

 

 

 

 

 

Video

 

or

 

 

 

 

 

 

 

 

 

 

 

 

Component

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDMI1

(or PC input)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDMI2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDMI3

 

 

 

 

 

 

 

 

 

 

 

Pressing [CHL] reverses the direction of the input modes.

5Switching Audio Mode

INTRODUCTION

 

This section describes how to switch the audio in the analog mode and how

 

to switch the audio language in the digital mode.

 

TV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press [AUDIO] to display the currently selected

 

PREPARATION

audio mode. While receiving an MTS broadcast,

 

 

 

press repeatedly to cycle through the available audio

 

 

channel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAP / STEREO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When all audio are available

WATCHING

 

SAP / STEREO

 

 

SAP / MONO

 

 

 

 

 

 

SAP / STEREO

 

 

TV

 

 

 

 

 

 

 

 

 

 

 

 

When stereo and monaural audio are available

 

MONO / STEREO

 

 

MONO / STEREO

 

 

 

OPTIONAL

SAP / MONO

 

 

SAP / MONO

When SAP and monaural audio are available

 

 

 

 

 

 

 

 

SETTING

 

 

 

MONO

When only monaural audio is available

 

 

 

 

(cannot be switched)

 

 

 

 

 

STEREO

TROUBLESHOOTING

 

: Outputs stereo-audio

 

 

SAP

 

: Outputs second audio program

 

MONO

 

: Outputs mono-audio

 

DTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Press [AUDIO] to display the currently selected

 

INFORMATION

language and the number of available languages.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

English 1/3

 

 

 

 

 

2Press [AUDIO] repeatedly to cycle through the available audio languages.

Available languages differ depending on the broadcast. “Other” is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French.

Note:

[AUDIO] does not control external audio devices.

The information display will automatically disappear in a few seconds.

15

EN

Page 15
Image 15
FUNAI LC320EMX owner manual 5Still Mode, 5Switching Each Input Mode, 5Switching Audio Mode