INSTALLATION INSTRUCTIONS

Step 14. Pre-test check list

Check to be sure power is off.

Open dishwasher door and remove all foam and cardboard packaging.

Read the Use & Care manual to familiarize yourself with the operation of the dishwasher.

Add two quarts of water to the bottom of the dishwasher to lubricate the pump seal.

Remove the protective film if present from the control panel and trim.

Check to be sure that wiring is secure under the dishwasher. Reattach connections if necessary.

Pull lower rack about half way out. Check to be sure it does not roll back into dishwasher or further out. If it does, relevel dishwasher.

Turn on water supply.

Check for plumbing leaks. Tighten connections if necessary.

Turn on the hot water faucet at the sink. Verify that temperature is at least 120¡F. Adjust the water heater to deliver water between 120¡ and 150¡F if necessary.

Let the dishwasher run through another fill and drain cycle. Check again to be sure there are no leaks.

At the end of the second drain, push the reset pad on electronic models. On dial models, unlatch the door and rotate the dial clockwise to the ÒOFFÓ position.

Step 16. Replace access panel and toekick

Refer to Figure T. Place the toekick against the legs of the dishwasher. Align the access panel to the dishwasher and tighten the two access panel screws. Align the toekick and make sure the bottom edge is against the floor. Insert and tighten the two toekick attachment screws, making sure the bottom edge of the toekick stays in contact with the floor.

Tighten 2

Access Panel Screws

Access Panel

Installation

Step 15. Dishwasher wet test check list

Turn on power supply.

Latch door.

Select normal cycle on push-button or electronic models.

On dial models, turn control dial just enough to start dishwasher. Be careful not to turn the dial past the first water fill. On electronic models, push start pad.

Check to be sure that water enters the dishwasher. This could take up to 4 minutes.

If water does not enter the dishwasher, check to be sure that water is turned on.

Check for leaks under the dishwasher. If a leak is found, turn off power supply, tighten connections and restore power.

Check for leaks around the door. A leak around the door could be caused by dishwasher door rubbing or hitting against adjacent cabinetry. Reposition the dishwasher if necessary.

The dishwasher will drain about 5 minutes after the first fill. Check drain lines. If leaks are found, turn off power, correct as necessary and restore power.

Toekick

Attachment Screws

Figure T

Step 17. Literature

Be sure to leave complete literature package and installation instructions with consumer.

21

Instructions

Page 21
Image 21
GE 500A200P047 Pre-test check list „ Check to be sure power is off, „ Turn on water supply, Dishwasher wet test check list

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.