Instructions

About the controls on the air conditioner

Instructions Safety

Vent Control

The vent control is located behind the front grille on the right side of the air discharge area. When CLOSED, only the air inside the room will be circulated and conditioned. When OPEN, the vent allows outdoor fresh air exchange.

To open or close the vent:

1.Remove the front grille.

2.Remove the vent card screw.

3.Remove vent card, turn it over and replace it by locating rear hole in card over locating pin inside air discharge and reattaching screw at front.

The unit leaves the factory set at the CLOSE position.

Locating hole

Locating hole

Screw hole

Screw hole

OPEN position

CLOSE position

(Mesh end toward back)

(Mesh end toward front)

and Cleaning Operating

Air Direction

Horizontal louvers

Remove the front grille

on the front grille

to adjust the vertical

let you control the

louvers side-to-side

air direction up and

to direct the air left

down.

or right.

Auxiliary Controls – Dip Switches (location varies by model)

Installation Instructions Care

The auxiliary dip switch controls are located behind the room cabinet—as shown in this figure.

The owner is responsible for checking switches and ensuring they are in the desired position.

Fan Cycle/Continuous - Cool

Fan Cycle/Continuous - Heat (on some models)

Class 2 (on some models)

No function (reserved for future use)

Consumer Support Troubleshooting Tips

Fan Cycle/Continuous - Cool

When this switch is enabled (UP), it allows the indoor

 

 

 

 

 

Fan Cycle/Continuous - Cool

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

fan to cycle on/off with the compressor. When this

 

 

 

 

 

 

 

 

 

 

 

 

switch is disabled (DOWN), ­it allows the indoor fan to run

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

continuously. The default setting is down (continuous).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fan Cycle/Continuous - Heat (on some models)

When this switch is enabled (UP), it allows the indoor

 

 

 

 

 

 

 

Fan Cycle/Continuous - Heat (on some models)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

fan to cycle on/off with the heater operation. When this

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

switch is disabled (DOWN), ­it allows the indoor fan to run

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

continuously. The default setting is UP (cyclic).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Class 2 - Remote Thermostat (on some models)

 

When this switch is enabled (UP), it allows the unit

 

 

 

 

 

 

 

 

 

Class 2 (on some models)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to operate with a Class 2 Remote Control Wall

 

 

 

 

 

 

 

 

 

 

 

 

 

Thermostat. The unit controls are disabled.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

The default setting is down (disabled).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 8
Image 8
GE AJCM 08 ACD installation instructions About the controls on the air conditioner