Instructions

Care and cleaning of the range.

Burner Caps and Heads (on sealed burners only)

Troubleshooting Tips Installation Instructions Operating Instructions Safety

Use a sewing needle or twist-tie to unclog the small hole in the burner head.

NOTE: Before removing the burner caps and heads, remember their size and location. Replace them in the same location after cleaning.

Burner caps

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Burner heads

For proper ignition, make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it.

The slits in the burner heads must be kept clean at all times for an even, unhampered flame.

Clogged or dirty burner ports or electrodes will not allow the burner to operate properly.

Any spill on or around an electrode must be carefully cleaned. Take care to not hit an electrode with anything hard or it could be damaged.

You should clean the burner caps and burner heads routinely, especially after bad spillovers, which could clog the openings in the burner heads. Lift off when cool.

To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20–30 minutes. For more stubborn stains, use a toothbrush.

After cleaning

Before putting the burner caps and heads back, shake out excess water and then dry them thoroughly by setting in a warm oven for 30 minutes.

NOTE: Do not use steel wool or scouring powders to clean the burners.

Replacement

Replace burner heads over the electrodes on the cooktop, in the correct locations according to their size.

Medium head

 

 

 

 

 

 

 

 

 

 

 

Small head

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front of range

Medium head

Large head

Make sure the slot in the burner head is positioned over the electrode.

Replace the matching size caps onto the heads. There is one large, one small and two medium caps.

Medium cap

 

 

 

 

 

 

 

 

 

 

 

Small cap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front of range

Consumer Support

Medium cap

Large cap

Make sure that the heads and caps are replaced in the correct locations.

NOTE: On some models, the burners are all the same size and power.

26

Page 25 Page 27
Page 26
Image 26
GE EGR3000 installation instructions Burner caps, Burner heads, After cleaning, Replacement
Page 25 Page 27

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents