Installation Preparation

PREPARE DISHWASHER ENCLOSURE

‡7KHURXJKFDELQHWRSHQLQJPXVWEHDWOHDVWµGHHSDQG 5/8”To 24” Wide. The opening should beto 35”max. height.

‡7KHGLVKZDVKHUPXVWEHLQVWDOOHGVRWKDWGUDLQKRVHLV no more than 10feet in length for proper drainage.

‡7KHGLVKZDVKHUPXVWEHIXOO\HQFORVHGRQWKHWRS

32-1/2" to 35"

 

24"

 

Underside of

 

4" Min.

 

Countertop

 

 

 

 

to Floor

 

 

Cabinets

 

 

 

 

 

 

 

6"

Square

 

 

 

and

 

 

 

 

 

24

Min

 

Plumb

 

 

 

 

Floor MUST

 

 

 

Figure 1

be Even with

Plumbing and Electric Service

Room Floor.

 

Must Enter Shaded Area

 

 

&/($5$1&(6 When installed into a corner, allow 2” min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8” min. clearance from the front of the dishwasher for door opening. Figure 2

Countertop

Dishwasher

25-5/8"

Clearance for Door Opening 2" Minimum

Figure 2

DRAIN REQUIREMENTS

Follow local codes and ordinances.

‡Do not exceed 10 feet distance to drain.

‡Do not connect drain lines from other devices to the dishwasher drain hose.

‡Dishwasher must be connected to waste line with an air gap (not supplied) or 32” minimum high drain loop, depending on local codes and ordinances to prevent back flow into the dishwasher .

‡Air gap must be used if waste tee or disposer connection is less than 18”above the floor to prevent siphoning.

DRAIN PREPARATION

The type of drain installation depends on answers to the following questions:

†Do local codes or ordinances require an air gap?

†Will waste tee or disposer connection be less than 18”above the floor?

†Will installation have a drain loop less than 32” above floor?

If the answer to ANY of the 3 questions above is YES, 0HWKRG0867EHXVHG. Otherwise either Method 1

or Method 2 may be used. Figure 3 or Figure 4.

&$87,21

An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18”above the floor. Failure to provide the proper drain connection height with air gap or 32” minimum, high drain loop will result in improper draining of the dishwasher.

35(&$8&,Ï1

DEBE USARSE un espacio de aire si la manguera de drenaje se encuentra conectada a una T de eliminación o desecho inferior a 18” sobre el piso. No brindar la adecuada altura de conexión de drenaje con un espacio de aire o un circuito de desagüe de 32” como mínimo, provocará un drenaje inadecuado del lavaplatos.

Method 1 Air Gap with Waste Tee or Disposer

Figure 3

Method 2 High Drain with Waste Tee or Disposer

Provide a method to attach drain hose to underside of countertop.

 

 

32"

18""

32"

Min.

Min.

18"

Minin..

 

Min.

 

 

Figure 4

Install waste tee or disposer and air gap according to Manufacturer s instructions.

CABINET PREPARATION

‡Drill a 1-1/2” dia. hole in the cabinet wall within the shaded areas shown in Figure 1 for the drain hose connection. The hole should be smooth with no sharp edges.

3

Page 2 Page 4
Page 3
Image 3
GE GE 31-30263 05-10 Prepare Dishwasher Enclosure, Drain Requirements, Or Method 2 may be used. or Figure
Page 2 Page 4

GE 31-30263 05-10 specifications

The GE 31-30263 05-10 is a standout product in the realm of commercial and industrial motors, designed to deliver exceptional performance and efficiency. This model, manufactured by General Electric, is built to withstand rigorous operating conditions while providing reliable functionality across a range of applications.

One of the main features of the GE 31-30263 05-10 is its robust construction, which includes high-quality materials that ensure durability. The motor is engineered to handle varying load requirements, making it suitable for processes that demand consistent power output. Its design incorporates an efficient cooling system that prevents overheating during prolonged use, allowing it to maintain optimal operating temperatures even in high-demand settings.

Technologically, the GE 31-30263 05-10 is equipped with advanced motor control capabilities. It supports various control methods, including VFD (Variable Frequency Drive) compatibility, which enhances its versatility and adaptability to different industrial requirements. This feature allows users to precisely control the speed of the motor, leading to significant energy savings and greater operational efficiency.

Another noteworthy characteristic is the motor's low maintenance requirements. The GE 31-30263 05-10 is designed with features that minimize wear and tear, reducing the frequency and cost of repairs. This reliability translates to lower total cost of ownership, making it an attractive option for businesses looking to optimize their operational expenses.

In terms of efficiency, this motor operates at a high performance level, often exceeding industry standards for energy consumption. This makes it not only an environmentally friendly choice but also a financially wise investment, as it helps organizations reduce energy bills.

Overall, the GE 31-30263 05-10 is a versatile, durable, and efficient motor that stands out in the market. Its combination of advanced technology, robust build, and low maintenance needs positions it as an ideal solution for various industrial applications, from manufacturing to automation. Companies seeking a reliable motor for their operations will find that the GE 31-30263 05-10 meets and exceeds expectations, providing both performance and value.
Top Page Image Contents