Installation Instructions

PREPARE HOT WATER LINE

‡7KHOLQHPD\HQWHUIURP(LWKHUVLGHUHDURUIORRUZLWKLQWKH shaded area shown in Figure F. ‡7KHOLQHPD\SDVVWKURXJKWKHVDPHKROHDVWKH electrical cable and Drain hose. Or, Cut an additional 1-1/2” dia. hole to accommodate the water line.

If power cord with plug is used, water line Must not pass through power cord hole.

Shut-off1-1/2" Dia.

Valve Hole

Hot

4"

 

From

18" From Wall

Cabinet

 

Cabinet Face

3" From Floor

 

Figure 6

 

Water Line Connection

‡7XUQRIIWKHZDWHUVXSSO\

Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.) ‡:DWHUFRQQHFWLRQLVRQWKHOHIWVLGHRIWKHGLVKZDVKHU Install the hot water inlet line, using no less than 3/8” O.D. copper tubing. Route the line as shown in Figure F and extend forward at least 18”from rear wall. ‡$GMXVWZDWHUKHDWHUIRU)WR)WHPSHUDWXUH ‡)OXVKZDWHUOLQHWRFOHDQRXWGHEULV ‡7KHKRWZDWHUVXSSO\OLQHSUHVVXUHPXVWEH36,

&$87,21

Opening the door will cause the dishwasher to tip forward. Do not open the door until you are ready to install the dishwasher . If it is necessary to open the door, hold the top of the dishwasher securely with one hand and hold the door with the other hand.

35(&$8&,Ï1

Abrir la puerta hará que el lavaplatos se incline hacia adelante. No abra la puerta hasta que esté listo para instalar el lavaplatos. Si es necesario abrir la puerta, sostenga la parte superior del lavaplatos firmemente con una mano y sujete la puerta con la otra.

BEFORE YOU BEGIN

Locate and set aside the package containing

2 phillips head counter top mounting screws STOP and 2 additional toekickscrews (located in the

literature).

STEP 1 – CHECK DOOR BALANCE

To check the door balance,hold the top of the diswasher firmly.

Increase

Decrease

Figure G

Figure 7

‡2SHQWKHGRRUVORZO\LIWKHGRRUGURSVZKHQUHOHDVHG increase spring tension. If the door closes when released, decrease tension.

‡3XOOWKHVSULQJDGMXVWPHQWSLQRXWRIWKHKROHVLQVHUW in the next highest or lowest hole and test again. ‡$GMXVWERWKGRRUVSULQJVWRWKHVDPHWHQVLRQ ‡&RQWLQXHPRYLQJWKHVSULQJSLQXQWLOGRRULVEDODQFH

5

Page 4 Page 6
Page 5
Image 5
GE GE 31-30263 05-10 Installation Instructions, Prepare HOT Water Line, Before YOU Begin, Check Door Balance
Page 4 Page 6

GE 31-30263 05-10 specifications

The GE 31-30263 05-10 is a standout product in the realm of commercial and industrial motors, designed to deliver exceptional performance and efficiency. This model, manufactured by General Electric, is built to withstand rigorous operating conditions while providing reliable functionality across a range of applications.

One of the main features of the GE 31-30263 05-10 is its robust construction, which includes high-quality materials that ensure durability. The motor is engineered to handle varying load requirements, making it suitable for processes that demand consistent power output. Its design incorporates an efficient cooling system that prevents overheating during prolonged use, allowing it to maintain optimal operating temperatures even in high-demand settings.

Technologically, the GE 31-30263 05-10 is equipped with advanced motor control capabilities. It supports various control methods, including VFD (Variable Frequency Drive) compatibility, which enhances its versatility and adaptability to different industrial requirements. This feature allows users to precisely control the speed of the motor, leading to significant energy savings and greater operational efficiency.

Another noteworthy characteristic is the motor's low maintenance requirements. The GE 31-30263 05-10 is designed with features that minimize wear and tear, reducing the frequency and cost of repairs. This reliability translates to lower total cost of ownership, making it an attractive option for businesses looking to optimize their operational expenses.

In terms of efficiency, this motor operates at a high performance level, often exceeding industry standards for energy consumption. This makes it not only an environmentally friendly choice but also a financially wise investment, as it helps organizations reduce energy bills.

Overall, the GE 31-30263 05-10 is a versatile, durable, and efficient motor that stands out in the market. Its combination of advanced technology, robust build, and low maintenance needs positions it as an ideal solution for various industrial applications, from manufacturing to automation. Companies seeking a reliable motor for their operations will find that the GE 31-30263 05-10 meets and exceeds expectations, providing both performance and value.
Top Page Image Contents