Installation instructions.

CAUTION: Certain plumbing skills are needed for installation. If you are unsure about any part of the installation of this product, consult a professional plumber.

Unpacking and Inspection

Be sure to check the entire softener for any shipping damage or parts loss. Also note damage to the

shipping cartons. Contact the transportation company for all damage and loss claims. The manufacturer is not responsible for damages in transit.

Small parts, needed to install the softener, are on a skin-packed cardboard piece. To avoid loss of the small parts, keep them on the skin-pack until you are ready to use them.

Important Installation Recommendations

Read entire manual. Failure to follow all guidelines and rules could cause personal injury or property damage.

•Before you begin installation, read these Installation Instructions completely. Then, obtain all the materials and tools you will need to make the installation. Failure to properly install the softener voids the warranty.

•Check local codes. The installation must conform to them.

•In the Commonwealth of Massachusetts, Plumbing Code 248 CMR shall be adhered to. Consult with your licensed plumber.

•Use only lead-free solder and flux for all sweat-solder connections, as required by state and federal codes.

•Connect the softener to the main water supply pipe before or ahead of the water heater. DO NOT RUN HOT WATER THROUGH THE SOFTENER. Temperature of water passing through the softener must be less than 120°F.

•Use care when handling the softener. Do not turn upside down, drop, drag, or set on sharp protrusions.

•Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary. (Adding a pressure reducing valve may reduce the flow.)

•The softener works on 24 volt-60 Hz electrical power only. Be sure to use the included transformer. Be sure the electric outlet and transformer are in an inside location to protect from wet weather.

•See Where to Install the Softener section for more details.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The water should be tested periodically to verify that the system is performing satisfactorily.

Small parts remaining after the installation could be a choke hazard. Discard safely.

4

Page 3 Page 5
Page 4
Image 4
GE GXSF27B GNSF35Z GXSF39B Installation instructions, Unpacking and Inspection, Important Installation Recommendations
Page 3 Page 5

GXSF27B GNSF35Z GXSF39B specifications

The GE GXSF27B, GNSF35Z, and GXSF39B are part of General Electric's line of advanced water filtration systems designed to enhance water quality for residential use. Each model boasts unique features and technologies aimed at providing clean and safe drinking water while ensuring convenient and efficient operation.

The GE GXSF27B model is known for its high-capacity, high-flow filtration capabilities. This system can effectively reduce sediment, chlorine taste and odor, and other impurities that can affect water quality. The GXSF27B comes equipped with a user-friendly control panel that simplifies monitoring and maintenance. Its compact design allows for seamless installation in various spaces, making it an attractive option for homeowners seeking efficient filtration without the bulk.

In contrast, the GE GNSF35Z model excels in removing challenging contaminants, particularly those often found in municipal water supplies. It utilizes a three-stage filtration process that ensures thorough cleaning and purification. The GNSF35Z features advanced filtration media designed to capture particles smaller than traditional filters, providing an enhanced level of water quality. Its smart technology automatically alerts users when filter changes are needed, thus preventing the degradation of filtration performance.

The GE GXSF39B model is a go-to choice for households requiring a significant volume of filtered water. With a higher capacity than its counterparts, it can serve large families or those with greater consumption needs. The GXSF39B incorporates an innovative water softening component that helps reduce hard water scale buildup in plumbing, increasing the longevity of appliances. This system ensures that users enjoy soft, clean water while also extending the lifespan of their household items.

All three models share key characteristics such as easy installation and maintenance, energy-efficient operation, and durable construction that ensures longevity. With their robust design and advanced technologies, the GE GXSF27B, GNSF35Z, and GXSF39B provide homeowners with peace of mind, knowing that they are investing in a reliable water filtration solution. Ultimately, these GE models cater to various needs and preferences, making them solid choices for anyone prioritizing water quality in their home.
Top Page Image Contents