About the water filtration system.

Filter Cartridge Installation or Replacement

CAUTION: Never remove the sumps when water pressure is in the Water Filtration system.

1 Close the water supply/saddle valve to the filter. (See illustration in the Installation Overview section for location of the water supply valve.) Open the filtered water faucet.

2 Remove the sump, using the sump wrench tool provided, from the filter head by rotating the sump as shown in the below illustration. Be careful, the sump may be full of water. Be sure to keep the large o-ring seal.

3 If you are replacing a filter cartridge, remove and discard the used filter cartridge.

4 Be sure the inside of the sump is clean. Thoroughly wash the inside of the sump with hot, soapy water and rinse.

5 Remove the wrapper from the new filter cartridge and insert the filter cartridge in the sump. Some cartridges fit either way, while others fit only one way. Observe markings on the cartridge.

NOTE: The Water Filtration system uses two different types of filter cartridges. Be sure to install them correctly. Filter I cartridge should always be placed in the Filter I sump. Filter II cartridge should always be placed in the Filter II sump. See page 3 for a complete list of filter performance characteristics.

Turn sump wrench tool provided clockwise to remove sump

Sump

Bracket

OUTLET

INLET

Head

 

Cartridge

O-ring seal

 

 

 

Sump II

 

 

 

Sump I

 

 

 

 

 

 

TURN SUMP

 

 

 

 

 

 

 

 

 

 

 

TO INSTALL

Label

 

 

 

 

 

 

 

 

 

 

 

TURN SUMP

 

 

 

 

 

 

 

 

TO REMOVE

 

 

 

 

For Model GXSL03C (rev. 2)

FXSLC (rev. 2) Filter Set (600-Gallon Capacity)

Filter I – White with no end caps

Filter II – White with yellow end caps

For Model GXSV10C

FXSVC (rev. 2) Filter Set (600-Gallon Capacity)

Filter I – White with green end caps Filter II – Gray

Filter II

Filter I

6 Lightly lubricate the o-ring seal in the sump with clean food-grade silicone grease (silicone grease is available through GE Parts and Services: 1-800-626-2002, Part Number: WS60X10005). Be sure it is fully seated in its groove.

7 Hold the sump up to the filter head, aligning the center hole in the cartridge with the protrusion on the bottom of the head. Failure to obtain proper alignment may cause damage to the filter and/or filtration system, which will degrade filter performance.

8 Being careful not to cross-thread, rotate the sump onto the filter head and tighten securely by hand.

NOTE: If the sump will not tighten up to the head or if you feel resistance, you may have the cartridge in upside down or misaligned. Take the cartridge out and check for correct orientation or alignment and reassemble.

9 Repeat steps 2 through 8 for the Filter II cartridge in the Filter II sump.

10

Page 10
Image 10
GE GXSL03C, GXSV10C About the water filtration system, Filter Cartridge Installation or Replacement

GXSL03C, GXSV10C specifications

The GE GXSL03C and GXSV10C are two models in General Electric's range of water filtration systems, known for their innovative features and advanced technologies. Designed to provide clean and safe drinking water, these systems cater to a variety of needs, from residential households to more extensive applications.

The GE GXSL03C model is particularly notable for its compact design and efficiency. It incorporates a reverse osmosis filtration system, which is highly effective in removing impurities, harmful contaminants, and sediments from water. This model is equipped with a five-stage filtration process that includes pre-filters, post-filters, and a thin-film composite membrane, ensuring a thorough purification. It has a maximum flow rate that allows for convenient water delivery, making it suitable for daily use.

On the other hand, the GE GXSV10C boasts a higher capacity and is designed specifically for larger households or small businesses. This model also employs advanced filtration technology, including a multi-stage process that removes chlorine, lead, and other unwanted substances. A key feature of the GXSV10C is its built-in smart technology, which monitors the status of filters and indicates when replacements are due. This ensures optimal performance and convenience for users.

Both models highlight user-friendly designs, featuring easy-to-replace filters and straightforward installation processes. They come with detailed instructions and typically include necessary accessories for setup. Moreover, the compact nature of these systems allows for flexible installation options, including under-sink locations or in utility areas.

Durability is another strong characteristic of both the GXSL03C and GXSV10C. They are constructed from high-quality materials designed to withstand common wear and tear while maintaining performance over time. Additionally, GE backs these products with reliable customer service and support, ensuring users can easily access help when needed.

In summary, the GE GXSL03C and GXSV10C present powerful water purification solutions featuring advanced filtration technologies, user-friendly designs, and durability. Their focus on efficiency and performance makes them excellent choices for consumers seeking improved water quality in their homes or businesses. With these systems, customers can enjoy peace of mind knowing they are investing in reliable water filtration solutions.