Manuals / GE / Household Appliance / Heat Pump

GE QS1800V Mounting Bracket Right Angle Inlet Figure, Right Angle Inlet and Vertical Position

Models: QS1800V QS2800V

1 36

Download 36 pages 51.59 Kb

Page 11

Image 11

3.0PUMP INSTALLATION

3.1Inspection

Your pump was inspected and tested at the factory prior to shipment to ensure it meets the requirements of your order. It is suggested the pump be checked upon receipt for possible damage due to shipping. Any damage should be immediately reported to the carrier.

3.2Pump Mounting and Locations

The QSV Series pumps are intended for vertical mounting with the right angle inlet of the pump down. See Figure 2 for correct orientation. The weight of the pump and motor must be supported by setting the flat end of the outer housing on a rubber pad supported by a plate or angle. Attach the pump to the frame work of your system using ALL brackets included. Refer to Section 8.0 (Dimensional Drawing) for correct bracket placement.

Mounting Bracket

Right Angle Inlet

Figure 3.2

Right Angle Inlet and

Vertical Position

(QS2825V Shown)

Page 11

Image 11

GE QS1800V, QS2800V manual Mounting Bracket Right Angle Inlet Figure, Right Angle Inlet and Vertical Position, QS2825V Shown

Contents

For QS1800V and QS2800V Series GE Infrastructure Water & Process TechnologiesINSTALLATION OPERATION, AND MAINTENANCE MANUAL OSMONICS TONKAFLO PUMPS QSV SERIESPage Page 10.0 PageLIST OF TABLES LIST OF FIGURESPage 1.0INTRODUCTION Liquid End Motor Module Figure Pump and Motor LabelsM o d e l Q S 2 8 2 Pump Label Junction Box Motor Label0.25 Table Pump Performance Summary2875 rpm 90F 32C MAXIMUM OPERATING TEMPERATURE QS2825V Shown Mounting Bracket Right Angle Inlet FigureRight Angle Inlet and Vertical Position 3.3Operation Safeguards 3.4.2Discharge Piping Pump Installation3.4.5Discharge Screen Strainer Victaulic GasketWater Level 3.5Pump Priming - IMPORTANTQSV pumps are not designed to be self-priming Figure 3.4, Priming Pump Levelthe Single-PhaseController Figure Two Sources of Power toFigure Changing Motor Rotation Figure 3.7Electrical Grounding without Do notrun pump dry orREMEDIES T R O U B L E S H O O T I N G G U I D EPROBLEM POSSIBLE CAUSESREMEDIES T R O U B L E S H O O T I N G G U I D EPROBLEM POSSIBLE CAUSEScheck for continuity using an T R O U B L E S H O O T I N G G U I D EPROBLEM Motor wired improperlyPOSSIBLE CAUSES T R O U B L E S H O O T I N G G U I D EPROBLEM Motor wired improperlyREMEDIES T R O U B L E S H O O T I N G G U I D EPROBLEM POSSIBLE CAUSESMotor Module Figure Liquid End and Motor Module 6.0FIELD MAINTENANCE6.2Liquid End Removal and Installation Liquid End Remove Bolts and Washers 4PLQS2825V Shown Pull Liquid End Straight Out FigureRemoving Liquid End QS2825V Shown Motor Module Liquid End Figure Liquid End RemovalFigure Rejoining Liquid End to Motor Module Liquid End Coupling O-Ring Motor Shaft FigureComponent Detail QS2825V Shown Align Splines and Pull Together Replace Washers and Bolts7.1Motor Warranty Figure QS1800V and QS2800V Series 8.0DIMENSIONAL DRAWINGFigure Parts Schematic 9.0REPLACEMENT PARTS 9.1Parts SchematicPart Description Part DescriptionQS1800V QS2800V Part Number PartGE Infrastructure Water & Process Technologies PUMP MODEL NUMBER PUMP SERIAL NUMBER 10.0WARRANTYPage Asia/Pacific Sales GE Infrastructure Water & Process TechnologiesNorth American Sales Euro/Africa Sales