Power Supply Locations, Gas supply, Rear-Burner Box

Installation Preparation

POWER SUPPLY LOCATIONS

Gas supply:

These cooktops are shipped from the factory set for either natural gas or LP gas. Check to be sure you have the correct cooktop for the type of gas being used.

•The pressure regulator must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless of type of gas being used.

•The natural gas model is designed to operate at

5″ water column pressure. A regulator is required

at the natural gas source to provide a minimum of 6″ water column to the cooktop regulator.

•The liquid propane model is designed to operate at 10″ water column pressure. A regulator is required at the LP source to provide a minimum of 11″ water column to the cooktop regulator.

•Maximum inlet pressure for the regulator supplied with the cooktop is 14″ water column regardless of the gas being used.

For ease of installation, and if local codes permit, the gas supply line into the cooktop should be 1/2″ or 3/4″ ID flexible metal appliance connector, three to five feet long.

NOTE: Purchase new flexible line. DO NOT USE OLD,

PREVIOUSLY USED FLEXIBLE LINE.

•Make gas connection through rear wall, or on cabinet floor at rear, as illustrated.

1.Install the house gas supply at least 1″ from the back wall.

2.Locate the electrical outlet 12″ below the countertop.

Rear–Burner Box

Install a manual shut-off valve in the gas line in an easily accessible location outside the cooktop. Be sure you know how and where to shut off the gas supply to the cooktop. Install the electrical outlet 12″ below the countertop.

Electrical supply:

This cooktop features pilotless electric ignition for energy savings and reliability. It operates on a 120 volt, 60 Hz power supply. A separate circuit, protected by a 15 amp time delay fuse or circuit breaker, is required.

Optional Combination Installations

This cooktop may be installed in combination with a ZVB30 Monogram Downdraft Vent, a ZET1, ZEK938 or ZET938 Single Oven or a ZTD910 or ZKD910 Warming Drawer.

•The gas and electrical supply must be located where it will not interfere with vent housing, the oven or the warming drawer. Review pages 12 to 14 for additional installation requirements.

•A properly-grounded 3-prong receptacle should be located within reach of the cooktop’s four-foot power cord.

IMPORTANT: (Please read carefully). FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

• The power cord of this appliance is equipped with

a three-prong (grounding) plug which mates with a

standard three-prong grounding wall receptacle to

minimize the possibility of electric shock hazard

from this appliance.

The gas inlet is located on the bottom of the burner box, at the right rear.

2”

1-5/8”

Gas Inlet

12”

Gas

supply line

1”

min.

• The customer should have the wall receptacle and

circuit checked by a qualified electrician to make sure

the receptacle is properly grounded and has correct

polarity.

• Where a standard two-prong wall receptacle is

encountered, it is the personal responsibility and

obligation of the customer to have it replaced with

a properly grounded three-prong wall receptacle.

Do Not, Under Any Circumstances, Cut Or Remove The Third (Ground) Prong From The Power Cord.

Do not use an extension cord.

ZGU384NSMSS, ZGU384L, ZGU384LSMSS, ZGU384N specifications

The GE ZGU384N, ZGU384LSMSS, ZGU384L, and ZGU384NSMSS are premium gas cooktop models that exemplify quality, performance, and modern design. Each model is tailored to meet the diverse needs of home chefs, ensuring that cooking becomes an enjoyable and efficient experience.

The GE ZGU384N is known for its robust construction and reliability. It features a durable stainless steel surface that resists stains and scratches. The cooktop includes four sealed burners that provide precise heat control, which is crucial for achieving the desired cooking results. Its continuous grates offer a seamless surface for sliding pots and pans, enhancing usability. The model's high-output burner delivers intense heat for boiling water or searing meats quickly, while lower BTU burners are perfect for simmering sauces and maintaining delicate flavors.

The ZGU384LSMSS variant boasts a sleek design with a stainless steel finish that complements a modern kitchen aesthetic. It is equipped with backlit knobs that not only provide visual appeal but also enhance functionality by indicating when the burners are on. This model features advanced technology, including electronic ignition for easy, reliable starts, and an automatic re-ignition system that ensures safety by re-lighting the burner if it goes out.

In contrast, the ZGU384L model stands out with its combination of performance and accessibility. It incorporates innovative flame recognition technology that adjusts the flame intensity based on cooking needs, ensuring efficient fuel consumption. Additionally, the model features a dishwasher-safe grates design, which makes maintenance simpler for busy households.

Lastly, the ZGU384NSMSS brings advanced cooking features to the forefront with its reversible cast iron grates, which provide versatility in cooking styles. This model integrates smart features, allowing users to monitor cooking progress through their smartphones. Equipped with high-efficiency burners, it meets the needs of those who prioritize energy conservation without compromising cooking power.

Overall, the GE ZGU384 series combines cutting-edge features, safety, and usability, making them ideal options for both novice cooks and seasoned chefs alike. Whether it's the minimalist aesthetics, powerful burners, or user-friendly technologies, these cooktops are designed to enhance any culinary adventure.

GE ZGU384N, ZGU384LSMSS Power Supply Locations, Gas supply, Rear-Burner Box, Electrical supply

Models: ZGU384NSMSS ZGU384L ZGU384LSMSS ZGU384N