Table of Contents, Introduction | Generac Power Systems specs

Image 3

Generac Power Systems 005040-0, 005040-1, 005053-0, 005053-1, 005054-0, 005054-1 Table of Contents, Introduction

Contents

This manual should remain with the unit SHOULD ATTEMPT INSTALLATIONOwner’s Manual Liquid-cooled,Prepackaged Standby Generators INTRODUCTION AUTHORIZED SERVICE DEALER LOCATION‹OPERATION AND MAINTENANCE ‹HOW TO OBTAIN SERVICE INTRODUCTION Table of Contents GENERAL HAZARDS Despite the safe design of this generatorParts of the generator are rotating and/or hot ‹STANDARDS INDEX ELECTRICAL HAZARDSFIRE HAZARDS EXPLOSION HAZARDS 1.4GENERATOR AC CONNECTION SYSTEMS 1.2TRANSFER SWITCH1.1GENERATOR 1.3AUTOMATIC SYSTEM OPERATION Figure 1.4 - Low Oil Pressure Switch ‹1.7.1 LOW OIL PRESSURE SWITCH‹1.7.2 HIGH COOLANT TEMPERATURE SWITCH ‹1.7.3 LOW COOLANT LEVEL SWITCH 1.8UNPACKING 1.10 SPECIFICATIONS‹1.7.6 LOW BATTERY ‹1.8.1 UNPACKING PRECAUTIONS ‹ 1.10.2 GENERATOR 1.12RECONFIGURING THE FUEL SYSTEM FOR LP VAPORFigure 1.8 — Reconfigure the Fuel System 1.11 FUEL CONSUMPTION 1.14 COOLANT RECOMMENDATIONS 1.15 BEFORE INSTALLATION2.1STANDBY GENERATOR INSTALLATION 1.13 ENGINE OIL RECOMMENDATIONS ‹2.1.2 OTHER PUBLISHED STANDARDS 2.3GENERATOR MOUNTING AND SUPPORT2.4BASIC STANDBY ELECTRIC SYSTEM 2.2GENERATOR LOCATION 2.7GROUNDING THE GENERATOR 2.9USING AN ENGINEERED “GTS” TRANSFER SWITCH2.5EMERGENCY CIRCUIT ISOLATION METHOD 2.6TOTAL CIRCUIT ISOLATION METHOD Standby generators installed with automatic 2.10BATTERY INSTALLATIONPos2 OFF — Standard Prepackaged ATS Application ‹2.10.1 VENTED BATTERIES ‹2.11.1 PRIOR TO INITIAL START-UP 3.1ENGINEERED GTS TRANSFER SWITCH‹2.11.2 TRANSFER SWITCH 2.11 PREPARATION BEFORE START-UP 3.2CONTROL CONSOLE COMPONENTS ‹3.2.2 FAULT INDICATOR LEDS‹3.2.1 AUTO/OFF/MANUAL SWITCH ‹3.2.5 SET EXERCISE TIME SWITCH 3.4ENGINE GOVERNOR ADJUSTMENTS 3.3MANUAL TRANSFER AND START-UP‹3.2.6 SYSTEM READY LED 3.7WEEKLY EXERCISE CYCLE Figure 3.2 — Engine Governor AdjustmentFigure 3.3 - “Set Exercise Time” Switch 3.6AUTOMATIC OPERATION C. ONCE ANNUALLY 3.8CONTROL BOARD DIP SWITCH SETTINGSA. EVERY THREE MONTHS B. ONCE EVERY SIX MONTHS Figure 4.1 — Intake Manifold Installation 4.2EXHAUST MANIFOLD PROCEDURE4.3INTAKE MANIFOLD PROCEDURE 4.4CYLINDER HEAD PROCEDURE 4.7CHECKING FLUID LEVELS 4.8MAINTENANCE OWNER/ OPERATOR CAN PERFORM4.6OVERLOAD PROTECTION FOR ENGINE DC ELECTRICAL SYSTEM ‹4.8.9 INSPECT ENGINE GOVERNOR ‹4.8.11 CHANGING THE ENGINE AIR CLEANERFigure 4.4 – Setting the Spark Plug Gap ‹4.8.8 CHECK FAN BELT ‹4.9.3 BATTERY MAINTENANCE 4.9MISCELLANEOUS MAINTENANCE‹4.9.1 CLEANING THE GENERATOR ‹4.9.2 BATTERY Service Maintenance Interval Information 4.10 SCHEDULED MAINTENANCE Maintenance LevelTasks Maintenance CORRECTION TROUBLESHOOTING POINTSPROBLEM CAUSE Section 6 — Notes Section 7 - Electrical Data 26 Generac Power Systems, Inc Section 7 - Electrical Data 28 Generac Power Systems, Inc Section 7 - Electrical Data 30 Generac Power Systems, Inc Section 7 - Electrical Data 32 Generac Power Systems, Inc Section 7 - Electrical Data MOUNT ITEM PART NODESCRIPTION 31 7 11 Enclosure — Drawing No. 0E9720-D 54 36 30 0C2267 40 Generac Power Systems, Inc 0C2267 Engine — Drawing No. 0E9918-E 42 Generac Power Systems, Inc 0E9909 0E1028A I/N 0E8456 LOCKTIGHT 0F1659A Muffler — Drawing No. 0F2930-B Stepper Motor — Drawing No. 0E9979-C Radiator — Drawing No. 0E9965-D Installation Diagram — Drawing No. 0F1020-A Section 9 — Installation Diagram CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSPURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES 1-800-333-1322 EMISSION RELATED PARTS INCLUDE THE FOLLOWING EMISSION CONTROL SYSTEM WARRANTY P.O. BOX 297 • WHITEWATER, WI WARRANTY SCHEDULETHIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING GENERAC POWER SYSTEMS, INC