Generac Power Systems 04758-2, 04759-2, 04760-2 guide

Image 14

Generac Power Systems 04758-2, 04759-2, 04760-2 Adjusting The Regulator Natural Gas Only, 1 - Dual Fuel Regulators

Contents

This manual should remain with the unit Models 04758-2 6 kW NG, 7 kW LP 04759-2 12 kW NG, 12 kW LP04760-2 13 kW NG, 15 kW LP Installation and Owner’s Manual ‹ HOW TO OBTAIN SERVICE ‹ CONTENTS‹ OPERATION AND MAINTENANCE INTRODUCTION Introduction Parts of the generator are rotating and/or hot GENERAL HAZARDSDespite the safe design of this generator during operation. Exercise care near running generators EXPLOSION HAZARDS ELECTRICAL HAZARDSFIRE HAZARDS ‹ STANDARDS INDEX 1.3 SYSTEM SET LED 1.1 UNPACKING/INSPECTION1.2 PROTECTION SYSTEMS DANGER Figure 1.2 - 12 kW/15 kW, V-twin GT-990/760 Engine 1.4 THE GENERATORFigure 1.1 - 7 kW, Single Cylinder GH-410 Engine ‹ 1.5.2 ENGINE 1.5 SPECIFICATIONS‹ 1.5.1 GENERATOR 1.7 FUEL CONSUMPTION 1.8 RECONFIGURING THE FUEL SYSTEM1.6 FUEL REQUIREMENTS AND RECOMMENDATIONS DANGER 1.9.1 GENERATOR 1.9 LOCATION1.8.2 12KW AND 15KW, 990CC ENGINES Figure 1.4 - Demand Regulator 1.9.2 TRANSFER SWITCH 1.9.2.1 7 kW, 12 kW and 15 kW Units 1.10 BATTERY INSTALLATION1.11 THE BATTERY Figure 1.5 - Battery Cable Connections 2.3 ELECTRICAL CHECKS 2.2 CHECK TRANSFER SWITCH OPERATION2.1 BEFORE INITIAL START-UP 2.4 GENERATOR TESTS UNDER LOAD 2.5 CHECKING AUTOMATIC OPERATION Figure 2.1 - Dual Fuel Regulators 2.6 ADJUSTING THE REGULATOR NATURAL GAS ONLYFigure 2.2 - Placement of Regulator Figure 2.3 - Single Cylinder Engine Governor Adjustment 2.7 ENGINE GOVERNOR ADJUSTMENTFigure 2.4 - V-twin Engine Governor Adjustment Figure 2.5 - V-twin Full Load Speed Adjust Screw 3.2 USING THE AUTO/OFF/MANUAL SWITCH FIGURE 2.8 VOLTAGE REGULATOR ADJUSTMENT3.1 BREAK-IN PROCEDURE Figure 2.6 - Voltage Adjustment Potentiometer 3.4 SEQUENCE OF AUTOMATIC OPERATION 3.3 AUTOMATIC TRANSFER OPERATION3.5 MANUAL TRANSFER OPERATION ‹ 3.5.1 TRANSFER TO GENERATOR POWER SOURCE ‹ 3.7.2 HIGH TEMPERATURE SWITCH ‹ 3.5.2 TRANSFER BACK TO UTILITY POWER SOURCE‹ 3.7.1 LOW OIL PRESSURE SWITCH Figure 3.2 - Manual Transfer Switch Operation 4.1 FUSE Figure 3.3 - Low Oil Pressure and High Temperature Switches4.2 CHECKING THE ENGINE OIL LEVEL ‹ 3.7.3 OVERCRANK 4.3 CHANGING THE ENGINE OIL 4.5 CHANGING THE ENGINE AIR CLEANER‹ 4.3.2 OIL CHANGE PROCEDURE 4.4 CHANGING THE OIL FILTER Figure 4.7 - 12 kW and 15 kW Engine Air Cleaner 4.7 BATTERY MAINTENANCEFigure 4.6 - 7 kW, Engine Air Cleaner Location Figure 4.8 - Setting the Spark Plug Gap 4.9 COOLING SYSTEM 4.8 ADJUSTING VALVE CLEARANCEFigure 4.10 - Valve Clearance Adjustment ‹ 4.12.1 REMOVAL FROM SERVICE 4.12 OUT OF SERVICE PROCEDURE‹ 4.12.2 RETURN TO SERVICE 4.10 ATTENTION AFTER SUBMERSION 4.13 SERVICE SCHEDULE CAUSE 5.1 TROUBLESHOOTING GUIDEPROBLEM CORRECTION Section 6 - Electrical Data 24 Generac Power Systems, IncENGINE WIRING CONNECTION CONTROL PANEL BOXCUSTOMER Electrical Schematic - 12 & 15 kW - Drawing No. 0D8501-B 26 Generac Power Systems, Inc Generac Power Systems, Inc 28 Generac Power Systems, Inc Section 6 - Electrical Data CONTROL PANEL BOX 224A 30 Generac Power Systems, Inc225A Electrical Schematic - 7 kW - Drawing No. 0D9014-C Section 7 - Exploded Views and Parts Lists 32 Generac Power Systems, Inc PART NO. QTY. DESCRIPTION 34 Generac Power Systems, Inc PART NO. QTY. DESCRIPTION 35, 36, 40 36 Generac Power Systems, Inc27, 28 PART NO. QTY DESCRIPTION 38 Generac Power Systems, Inc DESCRIPTION 40 Generac Power Systems, Inc 14 20 1.8 FT 1.25 FT 42 Generac Power Systems, Inc 1.33 FT 2.6 FT3 FT 44 Generac Power Systems, Inc Section 7 - Exploded Views and Parts Lists 46 Generac Power Systems, Inc Section 7 - Exploded Views and Parts Lists 48 Generac Power Systems, Inc Section 7 - Exploded Views and Parts Lists Section 8 - Mounting 50 Generac Power Systems, IncALL DIMENSIONS IN MILLIMETERS INCHES Guardian Air-cooled 7 kW, 12 Drawing No. 0D3739-B Section 9 - Notes PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES YOUR WARRANTY RIGHTS AND OBLIGATIONSMANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL SYSTEM WARRANTY EMISSION RELATED PARTS INCLUDE THE FOLLOWING WARRANTY SCHEDULE GENERAC POWER SYSTEMS TWO YEAR LIMITED WARRANTY FOR GUARDIANPREPACKAGED EMERGENCY AUTOMATIC STANDBY GENERATORS THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING